Impregnation of thermoplastic resin in jute fiber
mat

doi:10.1007/s11705-008-0030-3

Front. Chem. Sci. Eng.

2008, Vol. 2

Issue (2) : 145-149 https://doi.org/10.1007/s11705-008-0030-3

Impregnation of thermoplastic resin in jute fiber mat

LIU Xiaoye, DAI Gance

State-Key Laboratory of Chemical Engineering, East China University of Science and Technology;

Download: PDF(193 KB) HTML
Export: BibTeX | EndNote | Reference Manager | ProCite | RefWorks

Abstract Impregnation rate of thermoplastic resin (polypropylene) in jute fiber mat and influence of relative factors on impregnation were studied, aiming to develop the continuous melt impregnation technique and to investigate the effect of impregnation rate and temperature on processing conditions and mechanical properties of natural fiber mat-reinforced thermoplastics. Influence of pressure on porosity of fiber mat and effect of melt viscosity on impregnation rate were also investigated. The modified capillary rheometer was used as apparatus and experimental data were analyzed based on the one-dimension Darcy’s law. Results showed that at a given pressure, the impregnation rate is inversely proportional to melt viscosity and jute fiber mat has higher porosity than glass fiber mat. The architecture, compressibility, permeability and fiber diameter of jute fiber mat were compared with those of glass fiber mat and their effects on impregnation were discussed further. It could be seen that the average diameter of jute fiber is much bigger; the porosity of jute fiber mat is significantly higher and inner bundle impregnation does not exist in jute fiber mat. Therefore, it is not difficult to understand why the impregnation rate in jute fiber mat is 3.5 times higher and permeability is 14 times greater. Kozeny constants of jute and glass fiber mats calculated based on the capillary model are 2950 and 442, respectively.

Issue Date: 05 June 2008

Cite this article:

DAI Gance,LIU Xiaoye. Impregnation of thermoplastic resin in jute fiber mat[J]. Front. Chem. Sci. Eng., 2008, 2(2): 145-149.

URL:

https://academic.hep.com.cn/fcse/EN/10.1007/s11705-008-0030-3
https://academic.hep.com.cn/fcse/EN/Y2008/V2/I2/145

1	Bledzki A K Gassan J Composites reinforced withcellulose based fibersProgress in PolymerScience (Oxford) 1999 24(2)221274. doi:10.1016/S0079‐6700(98)00018‐5
2	Mohanty A K Misra M Drzal L T Sustainable bio-composites from renewable resources: opportunitiesand challenges in the green materials worldJournal of Polymers and the Environment 2002 10(1–2)1926. doi:10.1023/A:1021013921916
3	Lu H L Continuousmelt impregnation of PP/GMT. Dissertation for the Doctoral DegreeShanghaiEastChina University of Science and Technology 2001 112
4	Huang J Studyon processing of melt impregnation of GMT. Dissertation for the MasterDegreeShanghaiEast China University of Science and Technology 2001 52
5	Li M Huang J Dai G C Melt flow through glass fiber mat during GMT melt imregnationActa Materiae Compositae Sinica 2000 17(3)2832
6	Meng F G Zhang H M Yang F L Li Y S Zhang X W Study on the cake layer permeation in microfiltrationof sludge suspension based on fractal theoryJournal of Chemical Engineering of Chinese Universities 2006 20(5)763768
7	Gao X Liu L L Liu X F Zhang B Q Lin Y S Permeation of compressed and supercriticalfluids through porous membranesJournalof Chemical Engineering of Chinese Universities 2005 19(5)577582
8	Deshpande A P Srikanth A Praveen N Quantitative estimation of permeability with lattice Boltzmannsimulations: representiative porous media from composite processingCanadian Journal of Chemical Engineering 2005 83(5)808815
9	Breard J Henzel Y Trochu F Gauvin R Analysis of dynamicflows through porous mediaPolymer Composites 2003 3(24)391408. doi:10.1002/pc.10038
10	Chang C Y Hourng L W Study on void formation inresin transfer moldingPolymer Engineeringand Science 1998 5(38)809818
11	Mohan R V Shires D R Tamma K K Ngo N D Flow channels/fiberimpregnation studies for the process modeling/analysis of complexengineering structures manufactured by resin transfer moldingPolymer Composites 1998 19(5)527542. doi:10.1002/pc.10127
12	Slade J Pillai K M Advani S G Investigation of unsaturated flow in woven, braided andstitched fiber mats during mold-fillin in resin transfer moldingPolymer Composites 2001 22(4)491505. doi:10.1002/pc.10554
13	Liu X Y Dai G C The pretreatment of jute fiberand the mechnical properties of jute fiber mat reinfoced polypropyleneActa Materiae Compositae Sinica 2006 23(5)6874
14	Gao L F Impregnationprocess and mechanical properties of GMT. Dissertation for the Master'sDegreeShanghaiEast China University of Science and Technology 1996 1317
15	Dai G C Chen M H Fluid mechanics in chemicalengineeringBeijingChmeical Industry Press 2005
16	Astrom T B Pieps R B Advani S G On flow through aligned fiber beds and its applicationto composites processingJournal of CompositeMaterials 1992 26(9)13511373. doi:10.1177/002199839202600907
17	Advani S G Flowand rheology in polymer composite manufacturingNewarkElsevier Science 1994

Viewed

Full text

Abstract

Cited

Shared

Discussed