● Presented coupled system enhanced biodegradation of antibiotic chloramphenicol.

Exoelectrogenic biofilms have received considerable attention for their ability to enhance electron transfer between contaminants and electrodes in bioelectrochemical systems. In this study, we constructed anaerobic-aerobic-coupled upflow bioelectrochemical reactors (AO-UBERs) with different voltage application modes, voltages and hydraulic retention times (HRTs). In addition, we evaluated their capacity to remove chloramphenicol (CAP). AO-UBER can effectively mineralize CAP and its metabolites through electrical stimulation when an appropriate voltage is applied. The CAP removal efficiencies were ~81.1%±6.1% (intermittent voltage application mode) and 75.2%±4.6% (continuous voltage application mode) under 0.5 V supply voltage, which were ~21.5% and 15.6% greater than those in the control system without voltage applied, respectively. The removal efficiency is mainly attributed to the anaerobic chamber. High-throughput sequencing combined with catabolic pathway analysis indicated that electrical stimulation selectively enriched Megasphaera, Janthinobacterium, Pseudomonas, Emticicia, Zoogloea, Cloacibacterium and Cetobacterium, which are capable of denitrification, dechlorination and benzene ring cleavage, respectively. This study shows that under the intermittent voltage application mode, AO-UBERs are highly promising for treating antibiotic-contaminated wastewater.

• Physical, chemical and biological methods are explored for MPs removal.

Microplastics are an emerging threat and a big challenge for the environment. The presence of microplastics (MPs) in water is life-threatening to diverse organisms of aquatic ecosystems. Hence, the scientific community is exploring deeper to find treatment and removal options of MPs. Various physical, chemical and biological methods are researched for MPs removal, among which few have shown good efficiency in the laboratory. These methods also have a few limitations in environmental conditions. Other than finding a suitable method, the creation of legal restrictions at a governmental level by imposing policies against MPs is still a daunting task in many countries. This review is an effort to place all effectual MP removal methods in one document to compare the mechanisms, efficiency, advantages, and disadvantages and find the best solution. Further, it also discusses the policies and regulations available in different countries to design an effective global policy. Efforts are also made to discuss the research gaps, recent advancements, and insights in the field.

• Microplastics are widely found in both aquatic and terrestrial environments.

Microplastics (MPs) are distributed in the oceans, freshwater, and soil environment and have become major pollutants. MPs are generally referred to as plastic particles less than 5 mm in diameter. They consist of primary microplastics synthesized in microscopic size manufactured production and secondary microplastics generated by physical and environmental degradation. Plastic particles are long-lived pollutants that are highly resistant to environmental degradation. In this review, the distribution and possible sources of MPs in aquatic and terrestrial environments are described. Moreover, the adverse effects of MPs on natural creatures due to ingestion have been discussed. We also have summarized identification methods based on MPs particle size and chemical bond. To control the pollution of MPs, the biodegradation of MPs under the action of different microbes has also been reviewed in this work. This review will contribute to a better understanding of MPs pollution in the environment, as well as their identification, toxicity, and biodegradation in the ocean, freshwater, and soil, and the assessment and control of microplastics exposure.

• The sustainable approaches related to Fenton sludge reuse systems are summarized.

The classical Fenton oxidation process (CFOP) is a versatile and effective application that is generally applied for recalcitrant pollutant removal. However, excess iron sludge production largely restricts its widespread application. Fenton sludge is a hazardous solid waste, which is a complex heterogeneous mixture with Fe(OH)₃, organic matter, heavy metals, microorganisms, sediment impurities, and moisture. Although studies have aimed to utilize specific Fenton sludge resources based on their iron-rich characteristics, few reports have fully reviewed the utilization of Fenton sludge. As such, this review details current sustainable Fenton sludge reuse systems that are applied during wastewater treatment. Specifically, coagulant preparation, the reuse of Fenton sludge as an iron source in the Fenton process and as a synthetic heterogeneous catalyst/adsorbent, as well as the application of the Fenton sludge reuse system as a heterogeneous catalyst for resource utilization. This is the first review article to comprehensively summarize the utilization of Fenton sludge. In addition, this review suggests future research ideas to enhance the cost-effectiveness, environmental sustainability, and large-scale feasibility of Fenton sludge applications.

•Phages can be better indicators of enteric viruses than fecal indicator bacteria.

Wastewater is a breeding ground for many pathogens, which may pose a threat to human health through various water transmission pathways. Therefore, a simple and effective method is urgently required to monitor and treat wastewater. As bacterial viruses, bacteriophages (phages) are the most widely distributed and abundant organisms in the biosphere. Owing to their capacity to specifically infect bacterial hosts, they have recently been used as novel tools in water pollution control. The purpose of this review is to summarize and evaluate the roles of phages in monitoring pathogens, tracking pollution sources, treating pathogenic bacteria, infecting bloom-forming cyanobacteria, and controlling bulking sludge and biofilm pollution in wastewater treatment systems. We also discuss the limitations of phage usage in water pollution control, including phage-mediated horizontal gene transfer, the evolution of bacterial resistance, and phage concentration decrease. This review provides an integrated outlook on the use of phages in water pollution control.

• The overall global perspective of the PHMCS field was obtained.

In total, 9,552 documents were extracted from the Web of Science Core Collection and subjected to knowledge mapping and visualization analysis for the field of phytoremediation of HM-contaminated soil (PHMCS) with CiteSpace 5.7 R3 software. The results showed that (1) the number of publications increased linearly over the studied period. The top 10 countries/regions, institutions and authors contributing to this field were exhibited. (2) Keyword co-occurrence cluster analysis revealed a total of 8 clusters, including “Bioremediation,” “Arsenic,” “Biochar,” “Oxidative stress,” “Hyperaccumulation,” “EDTA,” “Arbuscular mycorrhizal fungi,” and “Environmental pollution” clusters (3) In total, 334 keyword bursts were obtained, and the 25 strongest, longest duration, and newest keyboard bursts were analyzed in depth. The strongest keyword burst test showed that the hottest keywords could be divided into 7 groups, i.e., “Plant bioremediation materials,” “HM types,” “Chelating amendments,” “Other improved strategies,” “Bioremediation characteristics,” “Risk assessment,” and “Other.” Almost half of the newest topics had emerged in the past 3 years, including “biochar,” “drought,” “health risk assessment,” “electrokinetic remediation,” “nanoparticle,” and “intercropping.” (4) In total, 9 knowledge base clusters were obtained in this study. The studies of Ali et al. (2013), Blaylock et al. (1997), Huang et al. (1997), van der Ent et al. (2013), Salt et al. (1995), and Salt (1998), which had both high frequencies and the strongest burst scores, have had the most profound effects on PHMCS research. Finally, future research directions were proposed.

Since the concept of emerging contaminants (ECs) was first proposed in 2001, the global scientific research of ECs has developed rapidly. In the past decades, great progress has been achieved in the scientific research of ECs in China, including the establishment of EC analysis method system, the evaluation of the pollution status, pollution characteristics and environmental risk of ECs in typical regions of China, and establishment of EC control technology system. Continuous progress in scientific research of ECs promoted China’s action on EC control. It is planned that the environmental risk of ECs will be generally controlled by 2035 in China. Priority ECs should be screened for environmental management. Although great efforts have been made, the EC control in China still faces tremendous challenges. It is necessary to bridge the gap between scientific research and decision-making management. Based on the science and technology study, various measures such as engineering, policy management and public participation should be combinedly adopted for EC control.

● Health hazards of plastic waste on environment are discussed.

The abundance of synthetic polymers has increased due to their uncontrolled utilization and disposal in the environment. The recalcitrant nature of plastics leads to accumulation and saturation in the environment, which is a matter of great concern. An exponential rise has been reported in plastic pollution during the corona pandemic because of PPE kits, gloves, and face masks made up of single-use plastics. The physicochemical methods have been employed to degrade synthetic polymers, but these methods have limited efficiency and cause the release of hazardous metabolites or by-products in the environment. Microbial species, isolated from landfills and dumpsites, have utilized plastics as the sole source of carbon, energy, and biomass production. The involvement of microbial strains in plastic degradation is evident as a substantial amount of mineralization has been observed. However, the complete removal of plastic could not be achieved, but it is still effective compared to the pre-existing traditional methods. Therefore, microbial species and the enzymes involved in plastic waste degradation could be utilized as eco-friendly alternatives. Thus, microbial biodegradation approaches have a profound scope to cope with the plastic waste problem in a cost-effective and environmental-friendly manner. Further, microbial degradation can be optimized and combined with physicochemical methods to achieve substantial results. This review summarizes the different microbial species, their genes, biochemical pathways, and enzymes involved in plastic biodegradation.

• AOA and comammox bacteria can be more abundant and active than AOB/NOB at WWTPs.

Nitrogen-cycling microorganisms play key roles at the intersection of microbiology and wastewater engineering. In addition to the well-studied ammonia oxidizing bacteria, nitrite oxidizing bacteria, heterotrophic denitrifiers, and anammox bacteria, there are some other N-cycling microorganisms that are less abundant but functionally important in wastewater nitrogen removal. These microbes include, but not limited to ammonia oxidizing archaea (AOA), complete ammonia oxidation (comammox) bacteria, dissimilatory nitrate reduction to ammonia (DNRA) bacteria, and nitrate/nitrite-dependent anaerobic methane oxidizing (NO_x-DAMO) microorganisms. In the past decade, the development of high-throughput molecular technologies has enabled the detection, quantification, and characterization of these minor populations. The aim of this review is therefore to synthesize the current knowledge on the distribution, ecological niche, and kinetic properties of these “overlooked” N-cycling microbes at wastewater treatment plants. Their potential applications in novel wastewater nitrogen removal processes are also discussed. A comprehensive understanding of these overlooked N-cycling microbes from microbiology, ecology, and engineering perspectives will facilitate the design and operation of more efficient and sustainable biological nitrogen removal processes.

• The PNA, denitratation/anammox, and DAMO/anammox process are reviewed together.

Anammox technology has been widely researched over the past 40-year from the laboratory-scale to full-scale. It is well-known that in actual applications, the solo application of anammox is not feasible. Since both ammonium and nitrite are prerequisites based on the reaction mechanism, the pre-treatment of wastewater is necessary. With the combination of anammox process and other pre-treatment processes to treat the actual wastewater, many types of anammox-based processes have been developed with distinct nitrogen removal performance. Thus, in order to heighten the awareness of researchers to the developments and accelerate the application of these processes to the treatment of actual wastewater, the main anammox-based processes are reviewed in this paper. It includes the partial nitritation/anammox process, the denitratation/anammox (PD/A) process, the denitrifying anaerobic methane oxidation/anammox (DAMO/A) process, and more complex deuterogenic processes. These processes have made the breakthroughs in the application of the anammox technology, such as the combination of nitrification and PD/A process can achieve stability and reliability of nitrogen removal in the treatment of mainstream wastewater, the PD/A process and the DAMO/A have brought about further improvements in the total nitrogen removal efficiency of wastewater. The diversity of functional microbe characteristics under the specific condition indicate the wide application potential of anammox-based processes, and further exploration is necessary. A whole waste treatment system concept is proposed through the effective allocation of above mentioned processes, with the maximum recovery of energy and resources, and minimal environmental impact.

• Fluorescence staining provides a fast and easy method to quantify microplastics.

Understanding the fate and toxicity of microplastics (MPs,<5 mm plastic particles) is limited by quantification methods. This paper summarizes the methods in use and presents new ones. First, sampling and pretreatment processes of MPs, including sample collection, digestion, density separation, and quality control are reviewed. Then the promising and convenient staining procedures and quantification methods for MPs using fluorescence dyes are reviewed. The factors that influence the staining of MPs, including their physicochemical properties, are summarized to provide an optimal operation procedure. In general, the digestion step is crucial to eliminate natural organic matter (NOM) to avoid interference in quantification. Chloroform was reported to be the most appropriate solvent, and 10–20 μg/mL are recommended as optimal dye concentrations. In addition, a heating and cooling procedure is recommended to maintain the fluorescence intensity of MPs for two months. After staining, a fluorescence microscope is usually used to characterize the morphology, mass, or number of MPs, but compositional analysis cannot be determined with it. These fluorescence staining methods have been implemented to study MP abundance, transport, and toxicity and have been combined with other chemical characterization techniques, such as Fourier transform infrared spectroscopy and Raman spectroscopy. More studies are needed to focus on the synthesis of novel dyes to avoid NOM’s interference. They need to be combined with other spectroscopic techniques to characterize plastic composition and to develop image-analysis methods. The stability of stained MPs needs to be improved.

• Bioaerosols are produced in the process of wastewater biological treatment.

Bioaerosols are defined as airborne particles (0.05–100 mm in size) of biological origin. They are considered potentially harmful to human health as they can contain pathogens such as bacteria, fungi, and viruses. This review summarizes the most recent research on the health risks of bioaerosols emitted from wastewater treatment plants (WWTPs) in order to improve the control of such bioaerosols. The concentration and size distribution of WWTP bioaerosols; their major emission sources, composition, and health risks; and considerations for future research are discussed. The major themes and findings in the literature are as follows: the major emission sources of WWTP bioaerosols include screen rooms, sludge-dewatering rooms, and aeration tanks; the bioaerosol concentrations in screen and sludge-dewatering rooms are higher than those outdoors. WWTP bioaerosols contain a variety of potentially pathogenic bacteria, fungi, antibiotic resistance genes, viruses, endotoxins, and toxic metal(loid)s. These potentially pathogenic substances spread with the bioaerosols, thereby posing health risks to workers and residents in and around the WWTP. Inhalation has been identified as the main exposure route, and children are at a higher risk of this than adults. Future studies should identify emerging contaminants, establish health risk assessments, and develop prevention and control systems.

• Retrofitting from CAS to MBR increased effluent quality and environmental benefits.

While a growing number of wastewater treatment plants (WWTPs) are being retrofitted from the conventional activated sludge (CAS) process to the membrane bioreactor (MBR) process, the debate on the techno-economy of MBR vs. CAS has continued and calls for a thorough assessment based on techno-economic valuation. In this study, we analyzed the operating data of 20 large-scale WWTPs (capacity≥10000 m³/d) and compared their techno-economy before and after the retrofitting from CAS to MBR. Through cost-benefit analysis, we evaluated the net profit by subtracting the operating cost from the environmental benefit (estimated by the shadow price of pollutant removal and water reclamation). After the retrofitting, the removal rate of pollutants increased (e.g., from 89.0% to 93.3% on average for NH₃-N), the average energy consumption increased from 0.40 to 0.57 kWh/m³, but the operating cost did not increase significantly. The average marginal environmental benefit increased remarkably (from 0.47 to 0.66 CNY/g for NH₃-N removal), leading to an increase in the average net profit from 19.4 to 24.4 CNY/m³. We further scored the technical efficiencies via data envelopment analysis based on non-radial directional distance functions. After the retrofitting, the relative cost efficiency increased from 0.70 to 0.73 (the theoretical maximum is 1), while the relative energy efficiency did not change significantly. The techno-economy is closely related to the effluent standard adopted, particularly when truncating the extra benefit of pollutant removal beyond the standard in economic modeling. The modeling results suggested that MBR is more profitable than CAS given stricter effluent standards.

Plastic pollution has been a legacy environment problems and more recently, the plastic particles, especially those ultrafine or small plastics particles, are widely recognized with increasing environmental and ecological impacts. Among small plastics, microplastics are intensively studied, whereas the physicochemical properties, environmental abundance, chemical states, bioavailability and toxicity toward organisms of nanoplastics are inadequately investigated. There are substantial difficulties in separation, visualization and chemical identification of nanoplastics due to their small sizes, relatively low concentrations and interferences from co-existing substances (e.g., dyes or natural organic matters). Moreover, detection of polymers at nanoscale is largely hampered by the detection limit or sensitivity for existing spectral techniques such as Transformed Infrared Spectroscopy (FTIR) or Raman Spectroscopy. This article critically examined the current state of art techniques that are exclusively reported for nanoplastic characterization in environmental samples. Based on their operation principles, potential applications and limitations of these analytical techniques are carefully analyzed.

The combustion of vinyl chloride (VC) after the train derailment accident in Ohio, USA in February, 2023 has caused widespread concern around the world. This paper tried to analyze several issues concerning the accident, including the appropriateness of the VC combustion in the emergency response in this accident, the meanings of so-called “controlled combustion”, the potential environmental risks caused by VC and combustion by-products, and follow-up work. In our view, this accident had surely caused environmental and health risks to some extent. Hence, a comprehensive environmental risk assessment is necessary, and then the site with risk should be comprehensively remediated, hazardous waste should be harmlessly treated as soon as possible. Finally, this accident suggests that further efforts should be taken to bridge the gap between chemical safety management and their environmental risk management.

•The history of biological and artificial water channels is reviewed.

Bioinspired and biomimetic membranes that contain biological transport channels or attain their structural designs from biological systems have been through a remarkable development over the last two decades. They take advantage of the exceptional transport properties of those channels, thus possess both high permeability and selectivity, and have emerged as a promising solution to existing membranes. Since the discovery of biological water channel proteins aquaporins (AQPs), extensive efforts have been made to utilize them to make separation membranes–AQP-based membranes, which have been commercialized. The exploration of AQPs’ unique structures and transport properties has resulted in the evolution of biomimetic separation materials from protein-based to artificial channel-based membranes. However, large-scale, defect-free biomimetic membranes are not available yet. This paper reviews the state-of-the-art biomimetic membranes and summarizes the latest research progress, platform, and methodology. Then it critically discusses the potential routes of this emerging area toward scalable applications. We conclude that an appropriate combination of bioinspired concepts and molecular engineering with mature polymer industry may lead to scalable polymeric membranes with intrinsic selective channels, which will gain the merit of both desired selectivity and scalability.

• The autotrophic nitrogen removal combining Feammox and Anammox was achieved.

Ferric iron reduction coupled with anaerobic ammonium oxidation (Feammox) is a novel ferric-dependent autotrophic process for biological nitrogen removal (BNR) that has attracted increasing attention due to its low organic carbon requirement. However, extracellular electron transfer limits the nitrogen transformation rate. In this study, activated carbon (AC) was used as an electron shuttle and added into an integrated autotrophic BNR system consisting of Feammox and anammox processes. The nitrogen removal performance, nitrogen transformation pathways and microbial communities were investigated during 194 days of operation. During the stable operational period (days 126–194), the total nitrogen (TN) removal efficiency reached 82.9%±6.8% with a nitrogen removal rate of 0.46±0.04 kg-TN/m³/d. The contributions of the Feammox, anammox and heterotrophic denitrification pathways to TN loss accounted for 7.5%, 89.5% and 3.0%, respectively. Batch experiments showed that AC was more effective in accelerating the Feammox rate than the anammox rate. X-ray photoelectron spectroscopy (XPS) analyses showed the presence of ferric iron (Fe(III)) and ferrous iron (Fe(II)) in secondary minerals. X-ray diffraction (XRD) patterns indicated that secondary iron species were formed on the surface of iron-AC carrier (Fe/AC), and Fe(III) was primarily reduced by ammonium in the Feammox process. The phyla Anaerolineaceae (0.542%) and Candidatus Magasanikbacteria (0.147%) might contribute to the Feammox process, and Candidatus Jettenia (2.10%) and Candidatus Brocadia (1.18%) were the dominative anammox phyla in the bioreactor. Overall, the addition of AC provided an effective way to enhance the autotrophic BNR process by integrating Feammox and anammox.

Over the past decades, the plastic production has been dramatically increased. Indeed, a category of small plastic particles mainly with the shapes of fragments, fibers, or spheres, called microplastics (particles smaller than 5 mm) and nanoplastics (particles smaller than 1 μm) have attracted particular attention. Because of its wide distribution in the environment and potential adverse effects to animal and human, microplastic pollution has been reported as a serious environment problem receiving increased attention in recent years. As one of the commonly detected emerging contaminants in the environment, recent evidence indicates that the concentration of microplastics show an increasing trend, for the reason that up to 12.7 million metric tons of plastic litter is released into aquatic environment from land-based sources each year. Furthermore, microplastic exposure levels of model organisms in laboratory studies are usually several orders of magnitude higher than those found in environment, and the microplastics exposure conditions are also different with those observed in the environment. Additionally, the detection of microplastics in feces indicates that they can be excreted out of the bodies of animal and human. Hence, great uncertainties might exist in microplastics exposure and health risk assessment based on current studies, which might be exaggerated. Policies reduce microplastic emission sources and hence minimize their environmental risks are determined. To promote the above policies, we must first overcome the technical obstacles of detecting microplastics in various samples.

• Fate of microplastics in integrated membrane system for water reuse was investigated.

Rare information on the fate of microplastics in the integrated membrane system (IMS) system in full-scale wastewater treatment plant was available. The fate of microplastics in IMS in a coastal reclaimed water plant was investigated. The removal rate of microplastics in the IMS system reached 93.2% after membrane bioreactor (MBR) treatment while that further increased to 98.0% after the reverse osmosis (RO) membrane process. The flux of microplastics in MBR effluent was reduced from 1.5 × 10¹³ MPs/d to 10.2 × 10¹¹ MPs/d while that of the RO treatment decreased to 2.7 × 10¹¹ MPs/d. Small scale fiber plastics (<200 μm) could break through RO system according to the size distribution analysis. The application of the IMS system in the reclaimed water plant could prevent most of the microplastics from being discharged in the coastal water. These findings suggested that the IMS system was more efficient than conventional activated sludge system (CAS) for the removal of microplastics, while the discharge of small scale fiber plastics through the IMS system should also not be neglected because small scale fiber plastics (<200 μm) could break through IMS system equipped with the RO system.

• Implication of COVID-19 on medical waste and MSW generation is studied.

It has been over ten months since the beginning of the 2019 coronavirus disease (COVID-2019), and its impact on solid waste management, especially medical waste, is becoming clearer. This study systematically reviews the potential influences of the COVID-19 pandemic on medical waste, personal protection equipment waste and municipal solid waste (MSW), and discusses the corresponding measures and policies of solid waste management in typical countries. The results show that the generation of medical waste from the pandemic increased significantly, with 18%‒425% growth. It is estimated that the daily output of COVID-19 medical waste increased from 200 t/d on Feb. 22 to over 29000 t/d at the end of September 2020 throughout the world. The use of personal protective equipment will continue to grow in the long-term, while the blockade and isolation measures greatly reduced the volume of commercial waste, especially for tourist cities, and part of this waste was transferred to household waste. Residents’ attitudes and behavior toward food waste have changed due to the COVID-19 pandemic. In response to the pandemic, international organizations and several countries have issued new policies and guidelines and adjusted their management strategies for medical waste and MSW treatment. The pandemic has brought specific challenges to the disposal capacity of medical waste worldwide. It has also brought about the stagnation of policies related to the reduction of plastic products and waste recycling. This study will provide some useful information for managers and governmental officials on effective solid waste management during and after the COVID-19 pandemic.

• Season and landform influenced spatiotemporal patterns of abundant and rare taxa.

The rare microbial biosphere provides broad ecological services and resilience to various ecosystems. Nevertheless, the biogeographical patterns and assembly processes of rare bacterioplankton communities in large rivers remain uncertain. In this study, we investigated the biogeography and community assembly processes of abundant and rare bacterioplankton taxa in the Yangtze River (China) covering a distance of 4300 km. The results revealed similar spatiotemporal patterns of abundant taxa (AT) and rare taxa (RT) at both taxonomic and phylogenetic levels, and analysis of similarities revealed that RT was significantly influenced by season and landform than AT. Furthermore, RT correlated with more environmental factors than AT, whereas environmental and spatial factors explained a lower proportion of community shifts in RT than in AT. The steeper distance–decay slopes in AT indicated higher spatial turnover rates of abundant subcommunities than rare subcommunities. The null model revealed that both AT and RT were mainly governed by stochastic processes. However, dispersal limitation primarily governed the AT, whereas the undominated process accounted for a higher fraction of stochastic processes in RT. River flow and suspended solids mediated the balance between the stochastic and deterministic processes in RT. The spatiotemporal dynamics and assembly processes of total taxa were more similar as AT than RT. This study provides new insights into both significant spatiotemporal dynamics and inconsistent assembly processes of AT and RT in large rivers.

• Pseudomonas mendocina was first reported for aerobic nitrate removal.

The problem of nitrate accumulation in aerobic tank and total nitrogen excessive discharge in effluent was very common in traditional livestock and poultry farming wastewater treatment systems owing to the lengthy process flow and low process control level. A strain LYX of aerobic bacterium was isolated from the activated sludge of a wastewater treatment system in a pig farm, which could remove nitrate effectively in aerobic tank and was identified Pseudomonas mendocina by 16S rRNA sequencing. Under the condition of nitrate as the sole nitrogen source, this strain removed over 90% of NO₃⁻-N with an initial concentration of 110 mg/L under aerobic conditions within 48 hours. Among them, 37.9% of NO₃⁻-N was assimilated into Bio-N, about 51.9% was reduced to gaseous nitrogen and less than 0.5% of nitrogen was replaced by NO₂⁻-N and NH₄⁺-N, 9.7% NO₃⁻-N remained in the effluent at the end. At the same time, four key genes (napA, nirK, norB and nosZ) related to nitrate nitrogen removal were expressed during the denitrification process of P. mendocina LYX, in which the transcription level of the indicator genes of this aerobic denitrifying bacterium (napA) was the highest. In addition, it was found with the ¹⁵N tracer technique that inoculation of this strain on sludge increased the amount of nitrogen loss from 9.26 nmol N/(g·h) to 23.835 nmol N/(g·h). Therefore, P. medocina LYX is a potential bioagent for advanced nitrogen removal by assimilating and reducing nitrate simultaneously in aerobic tanks.

● China’s implementation of the SC was systematically studied.

Persistent organic pollutants (POPs) are extremely harmful to the environment and human health; the Stockholm Convention on Persistent Organic Pollutants was therefore adopted by the international community in 2001 to eliminate or reduce the production, use, and emissions of POPs. China is the largest developing country that has signed the Stockholm Convention, and thus plays an important role in its implementation. This paper systematically studies the practice and achievements of China since it signed the Stockholm Convention 20 years ago. China has established an implementation guarantee system including institutions, implementation mechanisms, policies, law enforcement, and scientific and technological support. During the 20 years since the implementation of the Stockholm Convention, dichlorodiphenyltrichloroethane (DDT) and hexachlorocyclohexane (HCH) concentrations in the air have been steadily decreasing, and Perfluorooctane sulfonic acid/Perfluorooctane sulfonyl fluoride (PFOS/PFOSF) concentrations in water bodies have decreased. In the past 20 years, China has safely disposed of 6352.1 tons of pesticide persistent organic pollutants and 36998 sets of electrical equipment containing polychlorinated biphenyls (PCBs), with a disposal rate of 100%. In the future, China will further strengthen the construction of persistent organic pollutant monitoring networks, scientific research, publicity, education, and international cooperation to improve environmental quality, providing a reference for other countries to implement the Stockholm Convention.

• Total 174 subtypes of ARGs were detected by metagenomic analysis.

Microplastics existing widely in different matrices have been regarded as a reservoir for emerging contaminants. Mariculture systems have been observed to host microplastics and antibiotic resistance genes (ARGs). However, more information on proliferation of ARGs and metal resistance genes (MRGs) in mariculture system at the presence of microplastics is needed. This study used metagenomic analysis to investigate the distribution of ARGs and MRGs in water and microplastics of a typical mariculture pond. Total 18 types including 174 subtypes of ARGs were detected with the total relative abundances of 1.22/1.25 copies per 16S rRNA copy for microplastics/water. Chloramphenicol resistance genes were the dominant ARGs with the abundance of 0.35/0.42 copies per 16S rRNA copy for microplastics/water. Intergron intI1 was dominant gene among 6 detected mobile genetic elements (MGEs) with the abundance of 75.46/68.70 copies per 16S rRNA copy for water/microplastics. Total 9 types including 46 subtypes of MRGs were detected with total abundance of 5.02 × 10²/6.39 × 10² copies per 16S rRNA copy for water/ microplastics while genes resistant to copper and iron served as the dominant MRGs. Proteobacteria, Bacteroidetes, and Actinobacteria accounted for 84.2%/89.5% of total microbial community. ARGs with relatively high abundance were significantly positively related to major genera, MGEs, and MRGs. Microplastics in mariculture system could enrich most of MRGs and some ARGs to serve as potential reservoir for these pollutants. The findings of this study will provide important information on resistance gene pollution at presence of microplastics in the mariculture system for further proposing suitable strategy of environmental management.

• Emission of microbe from local environments is a main source of bioaerosols.

Recent pandemic outbreak of the corona-virus disease 2019 (COVID-19) has raised widespread concerns about the importance of the bioaerosols. They are atmospheric aerosol particles of biological origins, mainly including bacteria, fungi, viruses, pollen, and cell debris. Bioaerosols can exert a substantial impact on ecosystems, climate change, air quality, and public health. Here, we review several relevant topics on bioaerosols, including sampling and detection techniques, characterization, effects on health and air quality, and control methods. However, very few studies have focused on the source apportionment and transport of bioaerosols. The knowledge of the sources and transport pathways of bioaerosols is essential for a comprehensive understanding of the role microorganisms play in the atmosphere and control the spread of epidemic diseases associated with them. Therefore, this review comprehensively summarizes the up to date progress on the source characteristics, source identification, and diffusion and transport process of bioaerosols. We intercompare three types of diffusion and transport models, with a special emphasis on a widely used mathematical model. This review also highlights the main factors affecting the source emission and transport process, such as biogeographic regions, land-use types, and environmental factors. Finally, this review outlines future perspectives on bioaerosols.

• High-solid anaerobic digestion (HS-AD) of sewage sludge (SS) is overviewed.

High-solid anaerobic digestion (HS-AD) has been applied extensively during the last few decades for treating various organic wastes, such as agricultural wastes, organic fractions of municipal solid wastes, and kitchen wastes. However, the application of HS-AD to the processing of sewage sludge (SS) remains limited, which is largely attributable to its poor process stability and performance. Extensive research has been conducted to attempt to surmount these limitations. In this review, the main factors affecting process stability and performance in the HS-AD of SS are comprehensively reviewed, and the improved methods in current use, such as HS sludge pre-treatment and anaerobic co-digestion with other organic wastes, are summarised. Besides, this paper also discusses the characteristics of substance transformation in the HS-AD of SS with and without thermal pre-treatment. Research has shown that the HS effect is due to the presence of high concentrations of substances that may inhibit the function of anaerobic microorganisms, and that it also results in poor mass transfer, a low diffusion coefficient, and high viscosity. Finally, knowledge gaps in the current research on HS-AD of SS are identified. Based on these, it proposes that future efforts should be devoted to standardising the definition of HS sludge, revealing the law of migration and transformation of pollutants, describing the metabolic pathways by which specific substances are degraded, and establishing accurate mathematical models. Moreover, developing green sludge dewatering agents, obtaining high value-added products, and revealing effects of the above two on HS-AD of SS can also be considered in future.

• MPs were analyzed throughout three WWTPs with mixed domestic–industrial influents.

In wastewater treatment plants (WWTPs), microplastics (MPs) are complex, especially with mixed domestic–industrial influents. Conventional random grab sampling can roughly depict the distribution and characteristics of MPs but can not accurately reflect their daily fluctuations. In this study, the concentration, shape, polymer type, size, and color of MPs were analyzed by micro-Raman spectroscopy (detection limit of 0.05 mm) throughout treatment stages of three mixed domestic–industrial WWTPs (W1, W2, and W3) in Wuxi City, China, and the daily fluctuations of MPs were also obtained by dense grab sampling within 24 h. For influent samples, the average MP concentration of 392.2 items/L in W1 with 10% industrial wastewater was much higher than those in W2 (71.2 items/L with 10% industrial wastewater) and W3 (38.3 items/L with 60% industrial wastewater). White polyethylene granules with a diameter less than 0.5 mm from plastic manufacturing were the most dominant MPs in the influent of W1, proving the key role of industrial sources in MPs pollution. In addition, the daily dense sampling results showed that MP concentration in W1 influent fluctuated widely between 29.1 items/L and 4617.6 items/L within a day. Finally, few MPs (less than 4.0 items/L) in these WWTPs effluents were attributed to the effective removal of wastewater treatment processes. Thus, further attention should be paid to regulating the primary sources of MPs.

● China has pledged ambitious carbon peak and neutrality goals for mitigating global climate change.

China is the largest developing economy and carbon dioxide emitter in the world, the carbon neutrality goal of which will have a profound influence on the mitigation pathway of global climate change. The transition towards a carbon-neutral society is integrated into the construction of ecological civilization in China, and brings profound implications for China’s socioeconomic development. Here, we not only summarize the major challenges in achieving carbon neutrality in China, but also identify the four potential new opportunities: namely, the acceleration of technology innovations, narrowing regional disparity by reshaping the value of resources, transforming the industrial structure, and co-benefits of pollution and carbon mitigation. Finally, we provide five policy suggestions and highlight the importance of balancing economic growth and carbon mitigation, and the joint efforts among the government, the enterprises, and the residents.

• H. venusta TJPU05 showed excellent HN-AD ability at high salinity.

A novel salt-tolerant heterotrophic nitrification and aerobic denitrification (HN-AD) bacterium was isolated and identified as Halomonas venusta TJPU05 (H. venusta TJPU05). The nitrogen removal performance of H. venusta TJPU05 in simulated water (SW) with sole or mixed nitrogen sources and in actual wastewater (AW) with high concentration of salt and nitrogen was investigated. The results showed that 86.12% of NH₄⁺-N, 95.68% of NO₃^–-N, 100% of NO₂^–-N and 84.57% of total nitrogen (TN) could be removed from SW with sole nitrogen sources within 24 h at the utmost. H. venusta TJPU05 could maximally remove 84.06% of NH₄⁺-N, 92.33% of NO₃^–-N, 92.9% of NO₂^–-N and 77.73% of TN from SW with mixed nitrogen source when the salinity was above 8%. The application of H. venusta TJPU05 in treating AW with high salt and high ammonia nitrogen led to removal efficiencies of 50.96%, 47.28% and 43.19% for NH₄⁺-N, NO₃^–-N and TN respectively without any optimization. Furthermore, the activities of nitrogen removal–related enzymes of the strain were also investigated. The successful detection of high level activities of ammonia oxygenase (AMO), hydroxylamine oxidase (HAO), nitrate reductase (NAR) and nitrite reductase (NIR) enzymes under high salinity condition further proved the HN-AD and salt-tolerance capacity of H. venusta TJPU05. These results demonstrated that the H. venusta TJPU05 has great potential in treating high-salinity nitrogenous wastewater.