Air bearing center cross gap of neutron stress spectrometer sample table support system
Yang LI,Yunxin WU(),Hai GONG,Xiaolei FENG
State Key Laboratory of High Performance Complex Manufacturing, Changsha 410083, China; College of Mechanical and Electrical Engineering, Central South University, Changsha 410083, China; Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Central South University, Changsha 410083, China
A support system is the main load-bearing component of sample table for neutron stress spectrometer, and air bearing is an important element of a support system. The neutron stress spectrometer sample table was introduced, and the scheme for air bearing combination was selected. To study the performance of air bearing center cross gap, finite element models (FEMs) were established based on air motion and Reynolds equations, effects of air supply pressure, and gap parameters on the overturning moment and bearing capacity of air bearing center cross gap were analyzed. Results indicate that the width, depth, and height differences of the marble floor gap played important roles in the performance of the air bearing. When gap width is lesser than 1 mm and gap depth is lower than 0.4 mm, bearing capacity and overturning moment would vary rapidly with the variation of the width and depth. A gap height difference results in the bearing capacity dropping rapidly. The FEM results agree well with experimental results. Further, findings of the study could guide the design of the support system and marble floor.
. [J]. Frontiers of Mechanical Engineering, 2016, 11(4): 403-411.
Yang LI,Yunxin WU,Hai GONG,Xiaolei FENG. Air bearing center cross gap of neutron stress spectrometer sample table support system. Front. Mech. Eng., 2016, 11(4): 403-411.
Chen M F, Lin Y T. Static behavior and dynamic stability analysis of grooved rectangular aerostatic thrust bearings by modified resistance network method. Tribology International, 2002, 35(5): 329–338
https://doi.org/10.1016/S0301-679X(02)00012-9
2
Renn J, Hsiao C. Experimental and CFD study on the mass flow-rate characteristic of air through orifice-type restrictor in aerostatic bearings. Tribology International, 2004, 37(4): 309–315
https://doi.org/10.1016/j.triboint.2003.10.003
3
Luong T S, Potze<?Pub Caret?>W, Post J B, . Numerical and experimental analysis of aerostatic thrust bearings with porous restrictors. Tribology International, 2004, 37(10): 825–832
https://doi.org/10.1016/j.triboint.2004.05.004
Li Y, Ding H. Influences of the geometrical parameters of aerostatic thrust bearing with pocketed orifice-type restrictor on its performance. Tribology International, 2007, 40(7): 1120–1126
https://doi.org/10.1016/j.triboint.2006.11.001
6
Stout K J, Barrans S M. The design of aerostatic bearings for application to nanometre resolution manufacturing machine systems. Tribology International, 2000, 33(12): 803–809
https://doi.org/10.1016/S0301-679X(00)00118-3
Eleshaky M E. CFD investigation of pressure depressions in aerostatic circular thrust bearings. Tribology International, 2009, 42(7): 1108–1117
https://doi.org/10.1016/j.triboint.2009.03.011
10
Miyatake M, Yoshimoto S. Numerical investigation of static and dynamic characteristics of aerostatic thrust bearings with small feed holes. Tribology International, 2010, 43(8): 1353–1359
https://doi.org/10.1016/j.triboint.2010.01.002
11
Hou Y, Zhao X, Chen S, . Numerical analysis of externally pressurized gas thrust bearing with supply hole. Lubrication Engineering, 2008, 33(9): 1–3 (in Chinese)
12
Huang H, Liu P, Dong Z. The performances simulation of aerostatic thrust bearing. Computer Simulation, 2010, 28(3): 340–343 (in Chinese)
13
Long W. Study on loading characteristics of orifice compensated aerostatic thrust bearing. Dissertation for the Doctoral Degree. Harbin: Harbin Institute of Technology, 2010 (in Chinese)
14
Long W, Li J, Bao G. Application of FLUENT in the research of air bearing field. Machine Tool & Hydraulics, 2006, 34(6): 151–153
15
Zhang J. Research on higher stiffness aerostatic bearing. Dissertation for the Doctoral Degree. Xi’an: Northwestern Polytechnical University, 2006 (in Chinese)
https://doi.org/10.7666/d.y1189926
16
Li Y, Lin Y, Zhu H. Performances analysis of aerostatic bearing restricted by fan-shaped surface restrictor. Computer Simulation, 2013, 30(4): 243–247 (in Chinese)
17
Liu S. Numerical simulation and experimental investigation of the static characteristics of a vacuum preloaded aerostatic bearing. Dissertation for the Master’s Degree. Wuhan: Huazhong University of Science and Technology, 2012 (in Chinese)
18
Dun L, Liu Y, Chen S. Lubrication of Aerostatic Bearing. Harbin: Harbin Institute of Technology Press, 1990
19
He X. Dynamics of the ultra-precision positioning stage with gas-lubricated bearings. Dissertation for the Doctoral Degree. Wuhan: Huazhong University of Science and Technology, 2007 (in Chinese)
20
Yang X. Study of static and dynamic characteristics of planar aerostatic bearings. Dissertation for the Doctoral Degree. Wuhan: Huazhong University of Science and Technology, 2012 (in Chinese)
