Three-dimensional printable concrete requires further development owing to the challenges encountered, including its brittle behavior, high cement requirement for the buildability of layers, and anisotropic behavior in different directions. The aim of this study is to overcome these challenges. First, three-dimensional printable concrete mixtures were prepared using silica fume, ground blast furnace slag, and metakaolin, instead of cement, to reduce the amount of cement. Subsequently, the rheological and mechanical behaviors of these concretes were investigated. Second, three-dimensional printable concrete mixtures were prepared using 6-mm-long steel and synthetic fibers to eliminate brittleness and determine the effect of those fibers on the anisotropic behavior of the concrete. As a result of this study, it is understood that printable concretes with extremely low permeability and high buildability can be achieved using mineral additives. In addition, results showed that three-dimensional concrete samples containing short steel fibers achieve fracture energies up to 36 times greater than that of plain concrete. Meanwhile, its characteristic length values, as indicators of ductility, are 22 times higher than those of plain concrete. The weakest strength was recorded at the interfaces between layers. The bending and splitting tensile strengths of three-dimensional printed plain concrete samples were 15% and 19% lower than those of casted samples, respectively. However, the addition of fibers improved the mechanical strength of the interfaces significantly.
S C Paul, G P van Zijl, M J Tan, I Gibson. A review of 3D concrete printing systems and materials properties: Current status and future research prospects. Rapid Prototyping Journal, 2018, 24(4): 784–798 https://doi.org/10.1108/RPJ-09-2016-0154
2
B NematollahiM XiaJ Sanjayan. Current progress of 3D concrete printing technologies. In: Proceedings of the International Symposium on Automation and Robotics in Construction. Taipei, China: IAARC Publications, 2017
3
B Panda, G B Singh, C Unluer, M J Tan. Synthesis and characterization of one-part geopolymers for extrusion based 3D concrete printing. Journal of Cleaner Production, 2019, 220: 610–619 https://doi.org/10.1016/j.jclepro.2019.02.185
4
J G SanjayanB Nematollahi. 3D concrete printing for construction applications. In: Proceedings of the 3D Concrete Printing Technology. New York: Butterworth-Heinemann, 2019, 1–11
5
F Bos, R Wolfs, Z Ahmed, T Salet. Additive manufacturing of concrete in construction: Potentials and challenges of 3D concrete printing. Virtual and Physical Prototyping, 2016, 11(3): 209–225 https://doi.org/10.1080/17452759.2016.1209867
6
V N NerellaV Mechtcherine. Studying the printability of fresh concrete for formwork-free concrete onsite 3D printing technology (CONPrint3D). In: Proceedings of the 3D Concrete Printing Technology. New York: Butterworth-Heinemann, 2019, 333–347
7
C HoltL EdwardsL KeyteF MoghaddamB Townsend. Construction 3D printing. In: Proceedings of the 3D Concrete Printing Technology. New York: Butterworth-Heinemann, 2019, 349–370
8
Y WengB LuM J TanS Qian. Rheology and printability of engineered cementitious composites—A literature review. In: Proceedings of the Conference on Progress in Additive Manufacturing. Singapore: Research Publishing, 427–432
9
G Ji, T Ding, J Xiao, S Du, J Li, Z Duan. A 3D printed ready-mixed concrete power distribution substation: Materials and construction technology. Materials, 2019, 12(9): 1540 https://doi.org/10.3390/ma12091540
10
Z MalaebF AlSakkaF Hamzeh. 3D concrete printing: Machine design, mix proportioning, and mix comparison between different machine setups. In: Proceedings of the 3D Concrete Printing Technology. New York: Butterworth-Heinemann, 2019, 115–136
11
C Zhang, V N Nerella, A Krishna, S Wang, Y Zhang, V Mechtcherine, N Banthia. Mix design concepts for 3D printable concrete: A review. Cement and Concrete Composites, 2021, 122: 104155 https://doi.org/10.1016/j.cemconcomp.2021.104155
12
B Panda, M J Tan. Rheological behavior of high volume fly ash mixtures containing micro silica for digital construction application. Materials Letters, 2019, 237: 348–351 https://doi.org/10.1016/j.matlet.2018.11.131
13
C Liu, X Wang, Y Chen, C Zhang, L Ma, Z Deng, N Banthia. Influence of hydroxypropyl methylcellulose and silica fume on stability, rheological properties, and printability of 3D printing foam concrete. Cement and Concrete Composites, 2021, 122: 104158 https://doi.org/10.1016/j.cemconcomp.2021.104158
14
Z Liu, M Li, Y Weng, T N Wong, M J Tan. Mixture design approach to optimize the rheological properties of the material used in 3D cementitious material printing. Construction & Building Materials, 2019, 198: 245–255 https://doi.org/10.1016/j.conbuildmat.2018.11.252
15
Y Zhang, Y Zhang, W She, L Yang, G Liu, Y Yang. Rheological and harden properties of the high-thixotropy 3D printing concrete. Construction & Building Materials, 2019, 201: 278–285 https://doi.org/10.1016/j.conbuildmat.2018.12.061
16
M K Mohan, A V Rahul, K van Tittelboom, G de Schutter. Rheological and pumping behaviour of 3D printable cementitious materials with varying aggregate content. Cement and Concrete Research, 2021, 139: 106258 https://doi.org/10.1016/j.cemconres.2020.106258
17
S SkibickiM KaszyńskaN WahibM TechmanK FederowiczA ZielińskiM Hoffmann. Properties of composite modified with limestone powder for 3D concrete printing. In: Proceedings of the RILEM International Conference on Concrete and Digital Fabrication. Switzerland: Springer, 2020, 125–134
18
T Le, S A Austin, S Lim, R A Buswell, A G Gibb, T Thorpe. Mix design and fresh properties for high-performance printing concrete. Materials and Structures, 2012, 45(8): 1221–1232 https://doi.org/10.1617/s11527-012-9828-z
19
R J M Wolfs, F P Bos, T A M Salet. Triaxial compression testing on early age concrete for numerical analysis of 3D concrete printing. Cement and Concrete Composites, 2019, 104: 103344 https://doi.org/10.1016/j.cemconcomp.2019.103344
20
B Panda, S C Paul, L J Hui, Y W D Tay, M J Tan. Additive manufacturing of geopolymer for sustainable built environment. Journal of Cleaner Production, 2017, 167: 281–288 https://doi.org/10.1016/j.jclepro.2017.08.165
21
M Kaszyńska, S Skibicki, M Hoffmann. 3D concrete printing for sustainable construction. Energies, 2020, 13(23): 6351 https://doi.org/10.3390/en13236351
22
A S Suiker, R J Wolfs, S M Lucas, T A Salet. Elastic buckling and plastic collapse during 3D concrete printing. Cement and Concrete Research, 2020, 135: 106016 https://doi.org/10.1016/j.cemconres.2020.106016
23
Y Han, Z Yang, T Ding, J Xiao. Environmental and economic assessment on 3D printed buildings with recycled concrete. Journal of Cleaner Production, 2021, 278: 123884 https://doi.org/10.1016/j.jclepro.2020.123884
24
B Panda, S C Paul, M J Tan. Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material. Materials Letters, 2017, 209: 146–149 https://doi.org/10.1016/j.matlet.2017.07.123
25
Y Yang, C Wu, Z Liu, H Wang, Q Ren. Mechanical anisotropy of ultra-high performance fibre-reinforced concrete for 3D printing. Cement and Concrete Composites, 2022, 125: 104310 https://doi.org/10.1016/j.cemconcomp.2021.104310
26
A U Rehman, J H Kim. 3D concrete printing: A systematic review of rheology, mix designs, mechanical, microstructural, and durability characteristics. Materials, 2021, 14(14): 3800 https://doi.org/10.3390/ma14143800
27
Y Chen, K Jansen, H Zhang, C R Rodriguez, Y Gan, O Çopuroğlu, E Schlangen. Effect of printing parameters on interlayer bond strength of 3D printed limestone-calcined clay-based cementitious materials: An experimental and numerical study. Construction & Building Materials, 2020, 262: 120094 https://doi.org/10.1016/j.conbuildmat.2020.120094
28
T Ding, J Xiao, S Zou, Y Wang. Hardened properties of layered 3D printed concrete with recycled sand. Cement and Concrete Composites, 2020, 113: 103724 https://doi.org/10.1016/j.cemconcomp.2020.103724
29
V N Nerella, S Hempel, V Mechtcherine. Effects of layer-interface properties on mechanical performance of concrete elements produced by extrusion-based 3D-printing. Construction & Building Materials, 2019, 205: 586–601 https://doi.org/10.1016/j.conbuildmat.2019.01.235
30
R J M Wolfs, F P Bos, T A M Salet. Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing. Cement and Concrete Research, 2018, 106: 103–116 https://doi.org/10.1016/j.cemconres.2018.02.001
31
F P Bos, E Bosco, T A M Salet. Ductility of 3D printed concrete reinforced with short straight steel fibers. Virtual and Physical Prototyping, 2019, 14(2): 160–174 https://doi.org/10.1080/17452759.2018.1548069
32
L Pham, P Tran, J Sanjayan. Steel fibres reinforced 3D printed concrete: Influence of fibre sizes on mechanical performance. Construction & Building Materials, 2020, 250: 118785 https://doi.org/10.1016/j.conbuildmat.2020.118785
33
M Hambach, H Möller, T Neumann, D Volkmer. Portland cement paste with aligned carbon fibers exhibiting exceptionally high flexural strength (> 100 MPa). Cement and Concrete Research, 2016, 89: 80–86 https://doi.org/10.1016/j.cemconres.2016.08.011
34
T Ding, J Xiao, S Zou, X Zhou. Anisotropic behavior in bending of 3D printed concrete reinforced with fibers. Composite Structures, 2020, 254: 112808 https://doi.org/10.1016/j.compstruct.2020.112808
35
J van der Putten, A V Rahul, G De Schutter, K Van Tittelboom. Development of 3D printable cementitious composites with the incorporation of polypropylene fibers. Materials, 2021, 14(16): 4474 https://doi.org/10.3390/ma14164474
36
G Ma, Z Li, L Wang, F Wang, J Sanjayan. Mechanical anisotropy of aligned fiber reinforced composite for extrusion-based 3D printing. Construction & Building Materials, 2019, 202: 770–783 https://doi.org/10.1016/j.conbuildmat.2019.01.008
37
C Sun, J Xiang, M Xu, Y He, Z Tong, X Cui. 3D extrusion free forming of geopolymer composites: Materials modification and processing optimization. Journal of Cleaner Production, 2020, 258: 120986 https://doi.org/10.1016/j.jclepro.2020.120986
38
A V Rahul, M Santhanam, H Meena, Z Ghani. Mechanical characterization of 3D printable concrete. Construction & Building Materials, 2019, 227: 116710 https://doi.org/10.1016/j.conbuildmat.2019.116710
39
R J M Wolfs, F P Bos, T A M Salet. Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion. Cement and Concrete Research, 2019, 119: 132–140 https://doi.org/10.1016/j.cemconres.2019.02.017
40
V N NerellaS HempelV Mechtcherine. Micro- and macroscopic investigations on the interface between layers of 3D-printed cementitious elements. In: Proceedings of the International Conference on Advances in Construction Materials and Systems. Chennai: RILEM Publications, 2017, 8
41
T Wangler, E Lloret, L Reiter, N Hack, F Gramazio, M Kohler, M Bernhard, B Dillenburger, J Buchli, N Roussel, R Flatt. Digital concrete: Opportunities and challenges. RILEM Technical Letters, 2016, 1: 67–75 https://doi.org/10.21809/rilemtechlett.2016.16
42
N NolteH W KraussP VaradyD Lowke. Cold joints in additive manufacturing-Effect of extrusion and spraying on layer bonding. In: Proceedings of the 1st International Conference on Concrete and Digital Fabrication. Switzerland: Digital Concrete, 2018, 13–14
43
J PuttenG D SchutterK V Tittelboom. The effect of print parameters on the (micro) structure of 3D printed cementitious materials. In: Proceedings of the RILEM International Conference on Concrete and Digital Fabrication. Cham: Springer, 2018, 234–244
44
E Keita, H Bessaies-Bey, W Zuo, P Belin, N Roussel. Weak bond strength between successive layers in extrusion-based additive manufacturing: measurement and physical origin. Cement and Concrete Research, 2019, 123: 105787 https://doi.org/10.1016/j.cemconres.2019.105787
45
T MarchmentJ Sanjayan. Method of enhancing interlayer bond strength in 3D concrete printing. In: Proceedings of the RILEM International Conference on Concrete and Digital Fabrication. Cham: Springer, 2018, 148–156
46
S Bhattacherjee, A S Basavaraj, A V Rahul, M Santhanam, R Gettu, B Panda, E Schlangen, Y Chen, O Copuroglu, G Ma, L Wang, M A Basit Beigh, V Mechtcherine. Sustainable materials for 3D concrete printing. Cement and Concrete Composites, 2021, 122: 104156 https://doi.org/10.1016/j.cemconcomp.2021.104156
47
A Adesina. Recent advances in the concrete industry to reduce its carbon dioxide emissions. Environmental Challenges, 2020, 1: 100004 https://doi.org/10.1016/j.envc.2020.100004
E Worrell, L Price, N Martin, C Hendriks, L O Meida. Carbon dioxide emissions from the global cement industry. Annual Review of Energy and the Environment, 2001, 26(1): 303–329 https://doi.org/10.1146/annurev.energy.26.1.303
50
M Xia, B Nematollahi, J Sanjayan. Printability, accuracy and strength of geopolymer made using powder-based 3D printing for construction applications. Automation in Construction, 2019, 101: 179–189 https://doi.org/10.1016/j.autcon.2019.01.013
51
B NematollahiM XiaJ Sanjayan P Vijay. Effect of type of fiber on inter-layer bond and flexural strengths of extrusion-based 3D printed geopolymer. In: Proceedings of the Materials Science Forum. Baech: Trans Tech Publications Ltd., 2018, 155–162
52
S Muthukrishnan, S Ramakrishnan, J Sanjayan. Effect of alkali reactions on the rheology of one-part 3D printable geopolymer concrete. Cement and Concrete Composites, 2021, 116: 103899 https://doi.org/10.1016/j.cemconcomp.2020.103899
53
B Panda, C Unluer, M J Tan. Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing. Cement and Concrete Composites, 2018, 94: 307–314 https://doi.org/10.1016/j.cemconcomp.2018.10.002
54
M Xia, J G Sanjayan. Methods of enhancing strength of geopolymer produced from powder-based 3D printing process. Materials Letters, 2018, 227: 281–283 https://doi.org/10.1016/j.matlet.2018.05.100
55
Y W D TayB N PandaG H A TingN M N AhamedM J Tan C K Chua. Industry 4.0—Shaping the Future of the Digital World. China: CRC Press, 2020, 119–123
56
G H A Ting, Y W D Tay, M J Tan. Experimental measurement on the effects of recycled glass cullets as aggregates for construction 3D printing. Journal of Cleaner Production, 2021, 300: 126919 https://doi.org/10.1016/j.jclepro.2021.126919
57
Y W D TayY QianM J Tan. Printability region for 3D concrete printing using slump and slump flow test. Composites. Part B, Engineering, 2019, 174: 106968
58
(TC-50 FMC) RILEM. Determination of fracture energy of mortar and concrete by means of three-point bend tests on notched beams. Materials and Structures, 1985, 18: 285–290
59
A Hillerborg, M Modeer, P E Petersson. Analysis of crack formation and crack growths in concrete by means of fracture mechanics and finite elements. Cement and Concrete Research, 1976, 6(6): 773–781 https://doi.org/10.1016/0008-8846(76)90007-7
60
12390-3 EN. Testing Hardened Concrete—Part 3: Compressive Strength of Test Specimens. Brussels: European Committee for Standardization, 2009
61
12390-6 EN. Testing Hardened Concrete—Part 6: Tensile Splitting Strength of Test Specimens. Brussels: European Committee for Standardization, 2009
62
C1585 ASTM-2020. Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes. West Conshohocken, PA: ASTM International, 2020
63
C1202 ASTM-2005. Standard Test Method for Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration. West Conshohocken, PA: ASTM International, 2005
64
Z Çelik, A F Bingöl, A S Ağsu. Fresh, mechanical, sorptivity and rapid chloride permeability properties of self-compacting concrete with silica fume and fly ash. Iranian Journal of Science and Technology, Transactions of Civil Engineering, 2022, 46(2): 789–799 https://doi.org/10.1007/s40996-021-00676-x