Orientation effect of electropolishing characteristics of 316L stainless steel fabricated by laser powder bed fusion
Wei HAN1, Fengzhou FANG1,2()
1. Centre of Micro/Nano manufacturing Technology (MNMT-Dublin), University College Dublin, Dublin 4, Ireland 2. State Key Laboratory of Precision Measuring Technology and Instruments, Laboratory of Micro/Nano Manufacturing Technology (MNMT), Tianjin University, Tianjin 300072, China
3D metal printing process has attracted increasing attention in recent years due to advantages, such as flexibility and rapid prototyping. This study aims to investigate the orientation effect of electropolishing characteristics on different surfaces of 316L stainless steel fabricated by laser powder bed fusion (L-PBF), considering that the rough surface of 3D printed parts is a key factor limiting its applications in the industry. The electropolishing characteristics on the different surfaces corresponding to the building orientation in selective laser melting are studied. Experimental results show that electrolyte temperature has critical importance on the electropolishing, especially for the vertical direction to the layering plane. The finish of electropolished surfaces is affected by the defects generated during L-PBF process. Thus, the electropolished vertical surface has higher surface roughness Sa than the horizontal surface. The X-ray photoelectron spectroscopy spectra show that the electropolished horizontal surface has higher Cr/Fe element ratio than the vertical surface. The electropolished horizontal surface presents higher corrosion resistance than the vertical surface by measuring the anodic polarization curves and fitting the equivalent circuit of experimental electrochemical impedance spectroscopy.
W Han, F Z Fang. Two-step electropolishing of 316L stainless steel in a sulfuric acid-free electrolyte. Journal of Materials Processing Technology, 2020, 279: 116558 https://doi.org/10.1016/j.jmatprotec.2019.116558
2
X Yang, X Yang, R Sun, et al.. Obtaining atomically smooth 4H–SiC (0001) surface by controlling balance between anodizing and polishing in electrochemical mechanical polishing. Nanomanufacturing and Metrology, 2019, 2(3): 140–147
3
W Han, F Z Fang. Fundamental aspects and recent developments in electropolishing. International Journal of Machine Tools and Manufacture, 2019, 139: 1–23 https://doi.org/10.1016/j.ijmachtools.2019.01.001
4
F Z Fang. On atomic and close-to-atomic scale manufacturing- development trend of manufacturing technology. Chinese Mechani-cal Engineering, 2020, 31(9): 1009–1021 (in Chinese) https://doi.org/10.3969/j.issn.1004-132X.2020.09.001
5
X Wang, L Han, Y Geng, et al.. The simulation and research of etching function based on scanning electrochemical microscopy. Nanomanufacturing and Metrology, 2019, 2(3): 160–167 https://doi.org/10.1007/s41871-019-00047-1
6
P T Mathew, B J Rodriguez, F Z Fang. Atomic and close-to-atomic scale manufacturing: A review on atomic layer removal methods using atomic force microscopy. Nanomanufacturing and Metrology, 2020, 3(3): 167–186 https://doi.org/10.1007/s41871-020-00067-2
7
M Benedetti, E Torresani, M Leoni, et al.. The effect of post-sintering treatments on the fatigue and biological behavior of Ti-6Al-4V ELI parts made by selective laser melting. Journal of the Mechanical Behavior of Biomedical Materials, 2017, 71: 295–306 https://doi.org/10.1016/j.jmbbm.2017.03.024
8
K Alrbaey, D I Wimpenny, A A Al-Barzinjy, et al.. Electropolishing of re-melted SLM stainless steel 316L parts using deep eutectic solvents: 3 × 3 full factorial design. Journal of Materials Engineering and Performance, 2016, 25(7): 2836–2846 https://doi.org/10.1007/s11665-016-2140-2
9
J Mingear, B Zhang, D Hartl, et al.. Effect of process parameters and electropolishing on the surface roughness of interior channels in additively manufactured nickel-titanium shape memory alloy actuators. Additive Manufacturing, 2019, 27: 565–575 https://doi.org/10.1016/j.addma.2019.03.027
10
T Simson, A Emmel, A Dwars, et al.. Residual stress measurements on AISI 316L samples manufactured by selective laser melting. Additive Manufacturing, 2017, 17: 183–189 https://doi.org/10.1016/j.addma.2017.07.007
11
A Riemer, S Leuders, M Thöne, et al.. On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting. Engineering Fracture Mechanics, 2014, 120: 15–25 https://doi.org/10.1016/j.engfracmech.2014.03.008
12
E Lyczkowska-Widlak, P Lochynski, G Nawrat, et al.. Comparison of electropolished 316L steel samples manufactured by SLM and traditional technology. Rapid Prototyping Journal, 2019, 25(3): 566–580 https://doi.org/10.1108/RPJ-03-2018-0060
13
B Zhang, X Lee, J Bai, et al.. Study of selective laser melting (SLM) Inconel 718 part surface improvement by electrochemical polishing. Materials & Design, 2017, 116: 531–537 https://doi.org/10.1016/j.matdes.2016.11.103
14
V Urlea, V Brailovski. Electropolishing and electropolishing-related allowances for powder bed selectively laser-melted Ti-6Al-4V alloy components. Journal of Materials Processing Technology, 2017, 242: 1–11 https://doi.org/10.1016/j.jmatprotec.2016.11.014
15
V Urlea, V Brailovski. Electropolishing and electropolishing-related allowances for IN625 alloy components fabricated by laser powder-bed fusion. International Journal of Advanced Manufacturing Technology, 2017, 92(9–12): 4487–4499 https://doi.org/10.1007/s00170-017-0546-0
16
P Mercelis, J P Kruth. Residual stresses in selective laser sintering and selective laser melting. Rapid Prototyping Journal, 2006, 12(5): 254–265 https://doi.org/10.1108/13552540610707013
17
K Monroy, J Delgado, J Ciurana. Study of the pore formation on CoCrMo alloys by selective laser melting manufacturing process. Procedia Engineering, 2013, 63: 361–369 https://doi.org/10.1016/j.proeng.2013.08.227
18
S Leuders, M Thöne, A Riemer, et al.. On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance. International Journal of Fatigue, 2013, 48: 300–307 https://doi.org/10.1016/j.ijfatigue.2012.11.011
19
A Mertens, S Reginster, Q Contrepois, et al.. Microstructures and mechanical properties of stainless steel AISI 316L processed by selective laser melting. Materials Science Forum, 2014, 783–786: 898–903 https://doi.org/10.4028/www.scientific.net/MSF.783-786.898
20
H H Alsalla, C Smith, L Hao. Effect of build orientation on the surface quality, microstructure and mechanical properties of selective laser melting 316L stainless steel. Rapid Prototyping Journal, 2018, 24(1): 9–17 https://doi.org/10.1108/RPJ-04-2016-0068
21
D Kong, X Ni, C Dong, et al.. Anisotropy in the microstructure and mechanical property for the bulk and porous 316L stainless steel fabricated via selective laser melting. Materials Letters, 2019, 235: 1–5 https://doi.org/10.1016/j.matlet.2018.09.152
22
A Ahmadi, R Mirzaeifar, N S Moghaddam, et al.. Effect of manufacturing parameters on mechanical properties of 316L stainless steel parts fabricated by selective laser melting: A computational framework. Materials & Design, 2016, 112: 328–338 https://doi.org/10.1016/j.matdes.2016.09.043
23
X Q Ni, D C Kong, Y Wen, et al.. Anisotropy in mechanical properties and corrosion resistance of 316L stainless steel fabricated by selective laser melting. International Journal of Minerals Metallurgy and Materials, 2019, 26(3): 319–328 https://doi.org/10.1007/s12613-019-1740-x
24
H Gong, K Rafi, H Gu, et al.. Analysis of defect generation in Ti–6Al–4V parts made using powder bed fusion additive manufacturing processes. Additive Manufacturing, 2014, 1–4: 87–98 https://doi.org/10.1016/j.addma.2014.08.002
25
C Bruna-Rosso, A G Demir, B Previtali. Selective laser melting finite element modeling: Validation with high-speed imaging and lack of fusion defects prediction. Materials & Design, 2018, 156: 143–153 https://doi.org/10.1016/j.matdes.2018.06.037
26
W E King, H D Barth, V M Castillo, et al.. Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing. Journal of Materials Processing Technology, 2014, 214(12): 2915–2925 https://doi.org/10.1016/j.jmatprotec.2014.06.005
27
M Bayat, A Thanki, S Mohanty, et al.. Keyhole-induced porosities in laser-based powder bed fusion (L-PBF) of Ti6Al4V: High-fidelity modelling and experimental validation. Additive Manufacturing, 2019, 30: 100835 https://doi.org/10.1016/j.addma.2019.100835
28
Y Shang, Y Yuan, D Li, et al.. Effects of scanning speed on in vitro biocompatibility of 316L stainless steel parts elaborated by selective laser melting. International Journal of Advanced Manufacturing Technology, 2017, 92(9–12): 4379–4385 https://doi.org/10.1007/s00170-017-0525-5
29
X Q Ni, D C Kong, W Wu, et al.. Corrosion behavior of 316L stainless steel fabricated by selective laser melting under different scanning speeds. Journal of Materials Engineering and Performance, 2018, 27(7): 3667–3677 https://doi.org/10.1007/s11665-018-3446-z
30
D Kong, X Ni, C Dong, et al.. Bio-functional and anti-corrosive 3D printing 316L stainless steel fabricated by selective laser melting. Materials & Design, 2018, 152: 88–101 https://doi.org/10.1016/j.matdes.2018.04.058
31
S Wen, S Li, Q Wei, et al.. Effect of molten pool boundaries on the mechanical properties of selective laser melting parts. Journal of Materials Processing Technology, 2014, 214(11): 2660–2667 https://doi.org/10.1016/j.jmatprotec.2014.06.002
32
N Shayesteh Moghaddam, S E Saghaian, A Amerinatanzi, et al.. Anisotropic tensile and actuation properties of NiTi fabricated with selective laser melting. Materials Science and Engineering A, 2018, 724: 220–230 https://doi.org/10.1016/j.msea.2018.03.072
33
D Kong, C Dong, X Ni, et al.. Mechanical properties and corrosion behavior of selective laser melted 316L stainless steel after different heat treatment processes. Journal of Materials Science and Technology, 2019, 35(7): 1499–1507 https://doi.org/10.1016/j.jmst.2019.03.003
34
X Ni, D Kong, W Wu, et al.. Corrosion behavior of 316L stainless steel fabricated by selective laser melting under different scanning speeds. Journal of Materials Engineering and Performance, 2018, 27(7): 3667–3677 https://doi.org/10.1007/s11665-018-3446-z
35
W Han, F Z Fang. Electropolishing of 316L stainless steel using sulfuric acid-free electrolyte. Journal of Manufacturing Science and Engineering, 2019, 141(10): 101015 https://doi.org/10.1115/1.4044518
36
B Zhang, Y Li, Q Bai. Defect formation mechanisms in selective laser melting: A review. Chinese Journal of Mechanical Engineering, 2017, 30(3): 515–527 https://doi.org/10.1007/s10033-017-0121-5
37
A Sola, A Nouri. Microstructural porosity in additive manufacturing: The formation and detection of pores in metal parts fabricated by powder bed fusion. Journal of Advanced Manufacturing and Processing, 2019, 1(3): e10021 https://doi.org/10.1002/amp2.10021
38
E Liverani, S Toschi, L Ceschini, et al.. Effect of selective laser melting (SLM) process parameters on microstructure and mechani-cal properties of 316L austenitic stainless steel. Journal of Materials Processing Technology, 2017, 249: 255–263 https://doi.org/10.1016/j.jmatprotec.2017.05.042
39
C N Kuo, C K Chua, P C Peng, et al.. Microstructure evolution and mechanical property response via 3D printing parameter development of Al–Sc alloy. Virtual and Physical Prototyping, 2020, 15(1): 120–129 https://doi.org/10.1080/17452759.2019.1698967
40
X Nie, Z Chen, Y Qi, et al.. Effect of defocusing distance on laser powder bed fusion of high strength Al–Cu–Mg–Mn alloy. Virtual and Physical Prototyping, 2020, 15(3): 325–339 https://doi.org/10.1080/17452759.2020.1760895
41
D E Kimbrough, Y Cohen, A M Winer, et al.. A critical assessment of chromium in the environment. Critical Reviews in Environmental Science and Technology, 1999, 29(1): 1–46 https://doi.org/10.1080/10643389991259164
42
S J Lee, J J Lai. The effects of electropolishing (EP) process parameters on corrosion resistance of 316L stainless steel. Journal of Materials Processing Technology, 2003, 140(1–3): 206–210 https://doi.org/10.1016/S0924-0136(03)00785-4
43
H Luo, H Su, C Dong, et al.. Passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solution. Applied Surface Science, 2017, 400: 38–48 https://doi.org/10.1016/j.apsusc.2016.12.180
44
M Laleh, A E Hughes, S Yang, et al.. Two and three-dimensional characterisation of localised corrosion affected by lack-of-fusion pores in 316L stainless steel produced by selective laser melting. Corrosion Science, 2020, 165: 108394 https://doi.org/10.1016/j.corsci.2019.108394
45
R F Schaller, A Mishra, J M Rodelas, et al.. The role of microstructure and surface finish on the corrosion of selective laser melted 304L. Journal of the Electrochemical Society, 2018, 165(5): C234–C242 https://doi.org/10.1149/2.0431805jes
46
J B Jorcin, M E Orazem, N Pébère, et al.. CPE analysis by local electrochemical impedance spectroscopy. Electrochimica Acta, 2006, 51(8–9): 1473–1479 https://doi.org/10.1016/j.electacta.2005.02.128
47
A Shahryari, S Omanovic, J A Szpunar. Electrochemical formation of highly pitting resistant passive films on a biomedical grade 316LVM stainless steel surface. Materials Science and Engineering C, 2008, 28(1): 94–106 https://doi.org/10.1016/j.msec.2007.09.002
48
S Habibzadeh, L Li, D Shum-Tim, et al.. Electrochemical polishing as a 316L stainless steel surface treatment method: Towards the improvement of biocompatibility. Corrosion Science, 2014, 87: 89–100 https://doi.org/10.1016/j.corsci.2014.06.010
49
W Han, F Z Fang. Eco-friendly NaCl-based electrolyte for electropolishing 316L stainless steel. Journal of Manufacturing Processes, 2020, 58: 1257–1269 https://doi.org/10.1016/j.jmapro.2020.09.036
