1. College of Mechanical and Vehicle Engineering, Chongqing University, Chongqing 400044, China 2. State Key Laboratory of Mechanical Transmissions, Chongqing University, Chongqing 400044, China
Energy field-assisted machining technology has the potential to overcome the limitations of machining difficult-to-machine metal materials, such as poor machinability, low cutting efficiency, and high energy consumption. High-speed dry milling has emerged as a typical green processing technology due to its high processing efficiency and avoidance of cutting fluids. However, the lack of necessary cooling and lubrication in high-speed dry milling makes it difficult to meet the continuous milling requirements for difficult-to-machine metal materials. The introduction of advanced energy-field-assisted green processing technology can improve the machinability of such metallic materials and achieve efficient precision manufacturing, making it a focus of academic and industrial research. In this review, the characteristics and limitations of high-speed dry milling of difficult-to-machine metal materials, including titanium alloys, nickel-based alloys, and high-strength steel, are systematically explored. The laser energy field, ultrasonic energy field, and cryogenic minimum quantity lubrication energy fields are introduced. By analyzing the effects of changing the energy field and cutting parameters on tool wear, chip morphology, cutting force, temperature, and surface quality of the workpiece during milling, the superiority of energy-field-assisted milling of difficult-to-machine metal materials is demonstrated. Finally, the shortcomings and technical challenges of energy-field-assisted milling are summarized in detail, providing feasible ideas for realizing multi-energy field collaborative green machining of difficult-to-machine metal materials in the future.
D Dudzinski, A Devillez, A Moufki, D Larrouquère, V Zerrouki, J Vigneau. A review of developments towards dry and high speed machining of Inconel 718 alloy. International Journal of Machine Tools and Manufacture, 2004, 44(4): 439–456 https://doi.org/10.1016/S0890-6955(03)00159-7
3
D Bowden, Y Krysiak, L Palatinus, D Tsivoulas, S Plana-Ruiz, E Sarakinou, U Kolb, D Stewart, M Preuss. A high-strength silicide phase in a stainless steel alloy designed for wear-resistant applications. Nature Communications, 2018, 9(1): 1374 https://doi.org/10.1038/s41467-018-03875-9
4
W Zhao, S Z Wang, L Li, Y F Yang. Evaluation of cutting tool performance of end mills for titanium alloy components. Journal of South China University of Technology (Natural Science Edition), 2015, 43(9): 121–126 (in Chinese)
5
F Li. Wear of grinding wheels in high efficiency grinding of nickel-based superalloy. Thesis for the Master’s Degree. Nanjing: Nanjing University of Aeronautics and Astronautics, 2012 (in Chinese)
6
X L Zhang. Investigation of mechanism in high speed machining of 40CrNi2Si2MoVA ultra high strength process. Thesis for the Master’s Degree. Harbin: Harbin University of Science and Technology, 2016 (in Chinese)
7
G H He, M Y Wu, L X Li, L L Zou, C Cheng. Study on the formation mechanism of phase transformation and the influencing factors of cutting layer of the typical titanium alloy. Journal of Mechanical Engineering, 2018, 54(17): 133–141 (in Chinese)
8
W F Ding, Q Miao, B K Li, J H Xu. Review on grinding technology of nickel-based superalloys used for aero-engine. Journal of Mechanical Engineering, 2019, 55(1): 189–215 (in Chinese)
9
S Lin. Modeling and experimental investigation on workpiece temperature field for turn-milling of high strength steel. Dissertation for the Doctoral Degree. Wuhan: Huazhong University of Science and Technology, 2014 (in Chinese)
10
G H He, X L Liu, C H Wu, S Q Zhang, L L Zou, D J Li. Study on the negative chamfered edge and its influence on the indexable cutting insert’s lifetime and its strengthening mechanism. The International Journal of Advanced Manufacturing Technology, 2016, 84(5–8): 1229–1237 https://doi.org/10.1007/s00170-015-7778-7
11
L J Liu, M Lv, W G Wu, X J Zhu. Experimental study on the chip morphology in high speed milling Ti–6Al–4V alloy. Journal of Mechanical Engineering, 2015, 51(3): 196–205 (in Chinese) https://doi.org/10.3901/JME.2015.03.196
12
J X Ren, D A Hua. Principle of Grinding. Beijing: Electronic Industry Press, 2011 (in Chinese)
13
M Putz, M Cardone, M Dix, R Wertheim. Analysis of workpiece thermal behaviour in cut-off grinding of high-strength steel bars to control quality and efficiency. CIRP Annals, 2019, 68(1): 325–328 https://doi.org/10.1016/j.cirp.2019.04.023
14
S W Kim, D W Lee, M C Kang, J S Kim. Evaluation of machinability by cutting environments in high-speed milling of difficult-to-cut materials. Journal of Materials Processing Technology, 2001, 111(1–3): 256–260 https://doi.org/10.1016/S0924-0136(01)00529-5
15
P Koshy, R C Dewes, D K Aspinwall. High speed end milling of hardened AISI D2 Tool Steel (~58HRC). Journal of Materials Processing Technology, 2002, 127(2): 266–273 https://doi.org/10.1016/S0924-0136(02)00155-3
16
Z H Long, X B Wang, H C Wang. Factorial study on nonlinear characteristics of difficult-to-cut materials in high-speed cutting process. Journal of Mechanical Engineering, 2006, 42(1): 30–34 (in Chinese)
17
G L Liu, B Zou, C Z Huang, X Y Wang, J Wang, Z Q Liu. Tool damage and its effect on the machined surface roughness in high-speed face milling the 17-4PH stainless steel. The International Journal of Advanced Manufacturing Technology, 2016, 83(1–4): 257–264 https://doi.org/10.1007/s00170-015-7564-6
18
T D Marusich, M Ortiz. Modelling and simulation of high-speed machining. International Journal for Numerical Methods in Engineering, 1995, 38(21): 3675–3694 https://doi.org/10.1002/nme.1620382108
19
D Umbrello. Finite element simulation of conventional and high speed machining of Ti6Al4V alloy. Journal of Materials Processing Technology, 2008, 196(1–3): 79–87 https://doi.org/10.1016/j.jmatprotec.2007.05.007
20
G Chen, C Z Ren, X Y Yang, X M Jin, T Guo. Finite element simulation of high-speed machining of titanium alloy (Ti–6Al–4V) based on ductile failure model. The International Journal of Advanced Manufacturing Technology, 2011, 56(9–12): 1027–1038 https://doi.org/10.1007/s00170-011-3233-6
21
Q H Gong, C Sun, W Wang. High speed and high efficiency machining research of titanium alloy aircraft structure part and its application. Aeronautical Manufacturing Technology, 2016, (7): 26–32 (in Chinese)
22
M Z Liu, C H Li, H J Cao, S Zhang, Y Chen, B Liu, N Q Zhang, Z M Zhou. Research progresses and applications of CMQL machining technology. China Mechanical Engineering, 2022, 33(5): 529–550 (in Chinese)
23
K J Baumeister, F F Simon. Leidenfrost temperature—its correlation for liquid metals, cryogens, hydrocarbons, and water. ASME Journal of Heat and Mass Transfer, 1973, 95(2): 166–173 https://doi.org/10.1115/1.3450019
24
D H Hu, H Qiu, Q Li. Study on bubble dynamics inside droplets under local boiling. Journal of Engineering Thermophysics, 2021, 42(4): 1026–1031 (in Chinese)
25
P N Rao, R R Srikant. Sustainable machining utilizing vegetable oil based nanofluids. In: Proceedings of 2015 International Conference on Smart Technologies and Management for Computing, Communication, Controls, Energy and Materials. Avadi: IEEE, 2015, 664‒672 https://doi.org/10.1109/ICSTM.2015.7225495
26
D P Adler, W W S Hii, D J Michalek, J W Sutherland. Examining the role of cutting fluids in machining and efforts to address associated environmental/health concerns. Machining Science and Technology, 2006, 10(1): 23–58 https://doi.org/10.1080/10910340500534282
27
S Anton, S Andreas, B Friedrich. Heat dissipation in turning operations by means of internal cooling. Procedia Engineering, 2015, 100: 1116–1123 https://doi.org/10.1016/j.proeng.2015.01.474
28
F Pusavec, D Kramar, P Krajnik, J Kopac. Transitioning to sustainable production—part II: evaluation of sustainable machining technologies. Journal of Cleaner Production, 2010, 18(12): 1211–1221 https://doi.org/10.1016/j.jclepro.2010.01.015
29
R Sankaranarayanan, J H N Rajesh, K J Senthil, G M Krolczyk. A comprehensive review on research developments of vegetable-oil based cutting fluids for sustainable machining challenges. Journal of Manufacturing Processes, 2021, 67: 286–313 https://doi.org/10.1016/j.jmapro.2021.05.002
30
X Yang, H J Cao, Y P Chen, C L Zhang, L Zhou. Whole process cutting heat transfer model for high-speed dry hobbing. Journal of Mechanical Engineering, 2015, 51(19): 189–196 https://doi.org/10.3901/JME.2015.19.189
31
Y P Chen, H J Cao, X Yang. Research on load distribution characteristic on the cutting edge in high-speed gear hobbing process. Journal of Mechanical Engineering, 2017, 53(15): 181–187 https://doi.org/10.3901/JME.2017.15.181
32
H Zhang, J Q Dang, W W Ming, X W Xu, M Chen, Q L An. Cutting responses of additive manufactured Ti6Al4V with solid ceramic tool under dry high-speed milling processes. Ceramics International, 2020, 46(10): 14536–14547 https://doi.org/10.1016/j.ceramint.2020.02.253
33
M Salahshoor, Y B Guo. Cutting mechanics in high speed dry machining of biomedical magnesium–calcium alloy using internal state variable plasticity model. International Journal of Machine Tools and Manufacture, 2011, 51(78): 579–590 https://doi.org/10.1016/j.ijmachtools.2011.04.004
34
X Yang, H J Cao, Y B Du, L, XuY P Chen. Regulation and control method for tool temperature in high-speed dry cutting processes based on specific cutting energy. China Mechanical Engineering, 2018, 29(21): 2559–2564 (in Chinese)
35
G L Liu. High-speed machinability evaluation method of difficult-to-machine material for fatigue and corrosion resistance. Dissertation for the Doctoral Degree. Jinan: Shandong University, 2019 (in Chinese)
36
B J Li. Research on exergy efficiency model and coordinative optimization method of spindle system of high-speed dry hobbing machine tool. Dissertation for the Doctoral Degree. Chongqing: Chongqing University, 2019 (in Chinese)
37
L Lu, Q M Wang, B Z Chen, Y C Ao, D H Yu, C Y Wang, S H Wu, K H Kim. Microstructure and cutting performance of CrTiAlN coating for high-speed dry milling. Transactions of Nonferrous Metals Society of China, 2014, 24(6): 1800–1806 https://doi.org/10.1016/S1003-6326(14)63256-8
38
X G Li. Study on green manufacturing operation model and its main lines in machine tool industry. Dissertation for the Doctoral Degree. Chongqing: Chongqing University, 2012 (in Chinese)
39
X Yang. Transfer characteristics and quantification analysis method of the cutting heat in high-speed dry hobbing. Dissertation for the Doctoral Degree. Chongqing: Chongqing University, 2017 (in Chinese)
40
C H Li, J Y Li, S Wang, Q Zhang. Modeling and numerical simulation of the grinding temperature field with nanoparticle jet of MQL. Advances in Mechanical Engineering, 2013, 5: 986984 https://doi.org/10.1155/2013/986984
41
R Arunachalam, M A Mannan. Machinability of nickel-based high temperature alloys. Machining Science and Technology, 2000, 4(1): 127–168 https://doi.org/10.1080/10940340008945703
42
H W Song. Research on cutting mechanism of laser assisted machining for fused silica with experiments. Dissertation for the Doctoral Degree. Wuhan: Huazhong University of Science and Technology, 2019 (in Chinese)
43
M A Lajis, A K M N Amin, A N M Karim, H C D M Radzi, T L Ginta. Hot Machining of hardened steels with coated carbide inserts. American Journal of Engineering and Applied Sciences, 2009, 2(2): 421–427 https://doi.org/10.3844/ajeassp.2009.421.427
44
S Rajagopal, D J Plankenhorn, V L Hill. Machining aerospace alloys with the aid of a 15 kW laser. Journal of Applied Metalworking, 1982, 2(3): 170–184 https://doi.org/10.1007/BF02834035
45
K S Kim, C M Lee. A fundamental study on the prediction of preheating temperature of silicon nitride ceramics by using HPDL. Applied Mechanics and Materials, 2012, 229–231: 287–291 https://doi.org/10.4028/www.scientific.net/AMM.229-231.287
46
L Özler, A İnan, C Özel. Theoretical and experimental determination of tool life in hot machining of austenitic manganese steel. International Journal of Machine Tools and Manufacture, 2001, 41(2): 163–172 https://doi.org/10.1016/S0890-6955(00)00077-8
47
N Tosun, L Özler. A study of tool life in hot machining using artificial neural networks and regression analysis method. Journal of Materials Processing Technology, 2002, 124(1–2): 99–104 https://doi.org/10.1016/S0924-0136(02)00086-9
48
H T Ding, Y C Shin. Improving machinability of high chromium wear-resistant materials via laser-assisted machining. Machining Science and Technology, 2013, 17(2): 246–269 https://doi.org/10.1080/10910344.2013.780549
49
M Anderson, R Patwa, Y C Shin. Laser-assisted machining of Inconel 718 with an economic analysis. International Journal of Machine Tools and Manufacture, 2006, 46(14): 1879–1891 https://doi.org/10.1016/j.ijmachtools.2005.11.005
50
H T Ding, Y C Shin. Improvement of machinability of waspaloy via laser-assisted machining. The International Journal of Advanced Manufacturing Technology, 2013, 64(1–4): 475–486 https://doi.org/10.1007/s00170-012-4012-8
51
K J Suthar, J Patten, L Dong, H Abdel-Aal. Estimation of temperature distribution in silicon during micro laser assisted machining. In: Proceedings of the ASME 2008 International Manufacturing Science and Engineering Conference. Evanston: ASME, 2008, 301–309
52
S Sun, M Brandt, M S Dargusch. Thermally enhanced machining of hard-to-machine materials—a review. International Journal of Machine Tools and Manufacture, 2010, 50(8): 663–680 https://doi.org/10.1016/j.ijmachtools.2010.04.008
53
G Germain, P Dal Santo, J L Lebrun. Comprehension of chip formation in laser assisted machining. International Journal of Machine Tools and Manufacture, 2011, 51(3): 230–238 https://doi.org/10.1016/j.ijmachtools.2010.11.006
54
P P Song. Key fundamental research on laser assisted machining of silicon nitride ceramics. Dissertation for the Doctoral Degree. Zibo: Shandong University of Technology, 2020
55
S X Fang, H L Zhao, Q J Zhang. The application status and development trends of ultrasonic machining technology. Journal of Mechanical Engineering, 2017, 53(19): 22–32 https://doi.org/10.3901/JME.2017.19.022
56
F G Cao. Ultrasonic Machining. Beijing: Chemical Industry Press, 2014 (in Chinese)
57
X Y Zhang, Z H Lu, Z L Peng, D Y Zhang. High quality and efficient ultrasonic vibration cutting of titanium alloys. Journal of Mechanical Engineering, 2021, 57(5): 133–147 https://doi.org/10.3901/JME.2021.05.133
58
B Yılmaz, Ş Karabulut, A Güllü. A review of the chip breaking methods for continuous chips in turning. Journal of Manufacturing Processes, 2020, 49: 50–69 https://doi.org/10.1016/j.jmapro.2019.10.026
59
L J Ma, G J Liu, G C Wang. Study on mechanism of breaking chip of axial vibration drilling. Chinese Machinery Design and Manufacture, 2009, (2): 228–230 (in Chinese)
60
C B Ni, L D Zhu, J S Ning,Z C, YangC F Liu. Research on the characteristics of cutting force signal and chip in ultrasonic vibration-assisted milling of titanium alloys. Journal of Mechanical Engineering, 2019, 55(7): 207–216 (in Chinese) https://doi.org/10.3901/JME.2019.07.207
61
G C Verma, P M Pandey, U S Dixit. Estimation of workpiece-temperature during ultrasonic-vibration assisted milling considering acoustic softening. International Journal of Mechanical Sciences, 2018, 140: 547–556 https://doi.org/10.1016/j.ijmecsci.2018.03.034
62
X X Xu, Y L Mo, C S Liu, B Zhao. Drilling force of SiC particle reinforced aluminum-matrix composites with ultrasonic vibration. Key Engineering Materials, 2009, 416(21): 243–247 https://doi.org/10.4028/www.scientific.net/KEM.416.243
63
L B Zhang, L J Wang, X Y Liu, H W Zhao, X Wang, H Y Luo. Mechanical model for predicting thrust and torque in vibration drilling fibre-reinforced composite materials. International Journal of Machine Tools and Manufacture, 2001, 41(5): 641–657 https://doi.org/10.1016/S0890-6955(00)00105-X
64
B Zhao, F Chen, J L Tong. Theoretical and experimental research on material removal rate under ultrasonic grinding. Journal of Henan Polytechnic University, 2013, 32(3): 302–307 https://doi.org/10.3969/j.issn.1673-9787.2013.03.011
65
Y Kaynak, A Gharibi, U Yilmaz, U Köklü, K Aslantaş. A comparison of flood cooling, minimum quantity lubrication and high pressure coolant on machining and surface integrity of titanium Ti-5553 alloy. Journal of Manufacturing Processes, 2018, 34: 503–512 https://doi.org/10.1016/j.jmapro.2018.06.003
66
P Yan, Y M Rong, X B Wang, J Y Zhu, L Jiao, Z Q Liang. Effect of cutting fluid on precision machined surface integrity of heat-resistant stainless steel. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2018, 232(9): 1535–1548 https://doi.org/10.1177/0954405416673684
67
O Pecat, E Brinksmeier. Tool wear analyses in low frequency vibration assisted drilling of CFRP/Ti6Al4V stack material. Procedia CIRP, 2014, 14: 142–147 https://doi.org/10.1016/j.procir.2014.03.050
D Z Wang, S J Wu, J P Lin, G Q, GuoP Wang. Research on ultrasonic elliptical vibration micro-cutting Inconel 718 based on minimum quantity lubrication. Journal of Mechanical Engineering, 2021, 57(9): 264–272 (in Chinese) https://doi.org/10.3901/JME.2021.09.264
70
G C Verma, P M Pandey, U S Dixit. Modeling of static machining force in axial ultrasonic-vibration assisted milling considering acoustic softening. International Journal of Mechanical Sciences, 2018, 136: 1–6 https://doi.org/10.1016/j.ijmecsci.2017.11.048
71
Y Cao, J F Yin, W F Ding, J H Xu. Alumina abrasive wheel wear in ultrasonic vibration-assisted creep-feed grinding of Inconel 718 nickel-based superalloy. Journal of Materials Processing Technology, 2021, 297: 117241 https://doi.org/10.1016/j.jmatprotec.2021.117241
J Z Yang, C Y Wang, Y H Yuan,S M, YuanX B, Wang C L, LangW Q Li. State-of-the-art on MQL synergistic technologies and their applications. China Mechanical Engineering, 2022, 33(5): 506–528 (in Chinese)
74
A Race, I Zwierzak, J Secker, J Walsh, J Carrell, T Slatter, A Maurotto. Environmentally sustainable cooling strategies in milling of SA516: effects on surface integrity of dry, flood and MQL machining. Journal of Cleaner Production, 2021, 288: 125580 https://doi.org/10.1016/j.jclepro.2020.125580
75
V N Gaitonde, R S Karnik, J P Davim. Minimum Quantity Lubrication in Machining. John Wiley & Sons, Inc., 2013
S M Yuan, W L Han, G Y Zhu, X B, HouL Wang. Recent progress on the efficiency increasing methods of minimum quantity lubrication technology in green cutting. Journal of Mechanical Engineering, 2019, 55(5): 175–185 (in Chinese) https://doi.org/10.3901/JME.2019.05.175
78
K Weinert, I Inasaki, J W Sutherland, T Wakabayashi. Dry machining and minimum quantity lubrication. CIRP Annals, 2004, 53(2): 511–537 https://doi.org/10.1016/S0007-8506(07)60027-4
79
Y M Shao, O Fergani, B Z Li, S Y Liang. Residual stress modeling in minimum quantity lubrication grinding. The International Journal of Advanced Manufacturing Technology, 2016, 83(5–8): 743–751 https://doi.org/10.1007/s00170-015-7527-y
80
C C Han. Research on single crystal diamond turning technology of titanium alloy under nanofluids minimum quantity lubrication. Dissertation for the Doctoral Degree. Harbin: Harbin Institute of Technology, 2019 (in Chinese)
81
Y B Zhang. Grinding mechanism,force prediction model and experimental validation of vegetable oil based nanofluids minimum quantity lubrication. Dissertation for the Doctoral Degree. Qingdao: Qingdao University of Technology, 2018 (in Chinese)
82
Ç V Yıldırım. Experimental comparison of the performance of nanofluids, cryogenic and hybrid cooling in turning of Inconel 625. Tribology International, 2019, 137: 366–378 https://doi.org/10.1016/j.triboint.2019.05.014
83
Ç V Yıldırım, M Sarıkaya, T Kıvak, Ş Şirin. The effect of addition of hBN nanoparticles to nanofluid-MQL on tool wear patterns, tool life, roughness and temperature in turning of Ni-based Inconel 625. Tribology International, 2019, 134: 443–456 https://doi.org/10.1016/j.triboint.2019.02.027
84
T Singh, J S Dureja, M Dogra, M S Bhatti. Machining performance investigation of AISI 304 austenitic stainless steel under different turning environments. International Journal of Automotive and Mechanical Engineering, 2018, 15(4): 5837–5862 https://doi.org/10.15282/ijame.15.4.2018.10.0447
85
N Anand, A S Kumar, S Paul. Effect of cutting fluids applied in MQCL mode on machinability of Ti–6Al–4V. Journal of Manufacturing Processes, 2019, 43: 154–163 https://doi.org/10.1016/j.jmapro.2019.05.029
86
A Das, S K Patel, S R Das. Performance comparison of vegetable oil based nanofluids towards machinability improvement in hard turning of HSLA steel using minimum quantity lubrication. Mechanics & Industry, 2019, 20(5): 506–526 https://doi.org/10.1051/meca/2019036
87
Z Said, M Gupta, H Hegab, N Arora, A M Khan, M Jamil, E Bellos. A comprehensive review on minimum quantity lubrication (MQL) in machining processes using nano-cutting fluids. The International Journal of Advanced Manufacturing Technology, 2019, 105(5–6): 2057–2086 https://doi.org/10.1007/s00170-019-04382-x
88
A Roushan, U S Rao, K Patra, P Sahoo. Performance evaluation of tool coatings and nanofluid MQL on the micro-machinability of Ti–6Al–4V. Journal of Manufacturing Processes, 2022, 73: 595–610 https://doi.org/10.1016/j.jmapro.2021.11.030
89
Y Kaynak. Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining. The International Journal of Advanced Manufacturing Technology, 2014, 72(5–8): 919–933 https://doi.org/10.1007/s00170-014-5683-0
90
J Ni, Z Cui, C Wu, J B Sun, J H Zhou. Evaluation of MQL broaching AISI 1045 steel with sesame oil containing nano-particles under best concentration. Journal of Cleaner Production, 2021, 320: 128888 https://doi.org/10.1016/j.jclepro.2021.128888
91
D Q Gao, X J Zeng, N R He, J H Jia, S S Gao. Application of low temperature cutting technology in the processing of difficult materials. Manufacturing Technology and Machine Tool, 2020, (6): 39–43 https://doi.org/10.19287/j.cnki.1005-2402.2020.06.005
92
A Shokrani, V Dhokia, S T Newman. Investigation of the effects of cryogenic machining on surface integrity in CNC end milling of Ti–6Al–4V titanium alloy. Journal of Manufacturing Processes, 2016, 21: 172–179 https://doi.org/10.1016/j.jmapro.2015.12.002
93
D Fernández, A Sandá, I Bengoetxea. Cryogenic milling: study of the effect of CO2 cooling on tool wear when machining Inconel 718, Grade EAIN steel and Gamma TiAl. Lubricants, 2019, 7(1): 10 https://doi.org/10.3390/lubricants7010010
94
T Mulyana, E A Rahim, S N Md Yahaya. The influence of cryogenic supercritical carbon dioxide cooling on tool wear during machining high thermal conductivity steel. Journal of Cleaner Production, 2017, 164: 950–962 https://doi.org/10.1016/j.jclepro.2017.07.019
95
S Jozić, D Bajić, L Celent. Application of compressed cold air cooling: achieving multiple performance characteristics in end milling process. Journal of Cleaner Production, 2015, 100: 325–332 https://doi.org/10.1016/j.jclepro.2015.03.095
96
S Chaabani, P J Arrazola, Y Ayed, A Madariaga, A Tidu, G Germain. Comparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718. Journal of Materials Processing Technology, 2020, 285: 116780 https://doi.org/10.1016/j.jmatprotec.2020.116780
97
A M Khan, S Anwar, M Jamil, M M Nasr, M K Gupta, M Saleh, S Ahmad, M Mia. Energy, environmental, economic, and technological analysis of Al-GnP nanofluid-and cryogenic LN2-assisted sustainable machining of Ti–6Al–4V alloy. Metals, 2021, 11(1): 88 https://doi.org/10.3390/met11010088
98
A M Khan, W Zhao, L Li, M Alkahtani, S Hasnain, M Jamil, N He. Assessment of cumulative energy demand, production cost, and CO2 emission from hybrid CryoMQL assisted machining. Journal of Cleaner Production, 2021, 292: 125952 https://doi.org/10.1016/j.jclepro.2021.125952
99
M Z Liu, C H Li, Y B Zhang, Q L An, M Yang, T Gao, C Mao, B Liu, H J Cao, X F Xu, Z Said, S Debnath, M Jamil, H M Ali, S Sharma. Cryogenic minimum quantity lubrication machining: from mechanism to application. Frontiers of Mechanical Engineering, 2021, 16(4): 649–697 https://doi.org/10.1007/s11465-021-0654-2
100
L De Chiffre, J L Andreasen, S Lagerberg, I B Thesken. Performance testing of cryogenic CO2 as cutting fluid in parting/grooving and threading austenitic stainless steel. CIRP Annals, 2007, 56(1): 101–104 https://doi.org/10.1016/j.cirp.2007.05.026
101
B Chen, F X Xiong, H Q Tang, L He, S S Hu. Effect of cooling method on small diameter blind-hole drilling of new β-type dental Ti-Zr-Nb alloy. Journal of Manufacturing Processes, 2020, 59: 421–431 https://doi.org/10.1016/j.jmapro.2020.10.013
102
A Damir, B Shi, M H Attia. Flow characteristics of optimized hybrid cryogenic-minimum quantity lubrication cooling in machining of aerospace materials. CIRP Annals, 2019, 68(1): 77–80 https://doi.org/10.1016/j.cirp.2019.04.047
V Krishnaraj, S Samsudeensadham, R Sindhumathi, P Kuppan. A study on high-speed end milling of titanium alloy. Procedia Engineering, 2014, 97: 251–257 https://doi.org/10.1016/j.proeng.2014.12.248
105
A Ginting, M Nouari. Experimental and numerical studies on the performance of alloyed carbide tool in dry milling of aerospace material. International Journal of Machine Tools and Manufacture, 2006, 46(7–8): 758–768 https://doi.org/10.1016/j.ijmachtools.2005.07.035
106
A H Li, J Zhao, H B Luo, Z Q Pei, Z M Wang. Progressive tool failure in high-speed dry milling of Ti–6Al–4V alloy with coated carbide tools. The International Journal of Advanced Manufacturing Technology, 2012, 58(5–8): 465–478 https://doi.org/10.1007/s00170-011-3408-1
107
A H Li, J Zhao, H B Luo, W Zheng. Machined surface analysis in high-speed dry milling of Ti–6Al–4V alloy with coated carbide inserts. Advanced Materials Research, 2011, 325: 412–417 https://doi.org/10.4028/www.scientific.net/AMR.325.412
108
A H Li, J Zhao, Y H Zhou, X X Chen, D Wang. Experimental investigation on chip morphologies in high-speed dry milling of titanium alloy Ti–6Al–4V. The International Journal of Advanced Manufacturing Technology, 2012, 62(9–12): 933–942 https://doi.org/10.1007/s00170-011-3854-9
109
H Safari, S Sharif, S Izman, H Jafari. Surface integrity characterization in high-speed dry end milling of Ti–6Al–4V titanium alloy. The International Journal of Advanced Manufacturing Technology, 2015, 78(1–4): 651–657 https://doi.org/10.1007/s00170-014-6653-2
110
S Sharif, H Safari, S Izman, D Kurniawan. Effect of high-speed dry end milling on surface roughness and cutting forces of Ti–6Al–4V ELI. Applied Mechanics and Materials, 2014, 493: 546–551 https://doi.org/10.4028/www.scientific.net/AMM.493.546
111
Q L Niu, M Chen, W W Ming, Q L An. Evaluation of the performance of coated carbide tools in face milling TC6 alloy under dry condition. The International Journal of Advanced Manufacturing Technology, 2013, 64(5–8): 623–631 https://doi.org/10.1007/s00170-012-4043-1
112
J Liu, S S Zhu, X Deng, J Y Liu, Z P Wang, Z Qu. Cutting performance and wear behavior of AlTiN- and TiAlSiN-coated carbide tools during dry milling of Ti–6Al–4V. Acta Metallurgica Sinica, 2020, 33(3): 459–470 https://doi.org/10.1007/s40195-020-01010-6
113
J Zhou. Research on correlation technique and mechanism of high-speed cutting Ni-based superalloy GH4169. Dissertation for the Doctoral Degree. Harbin: Harbin Institute of Technology, 2012 (in Chinese)
114
W M Huang, J Zhao, S Y Wang. Necessity of multidimensional evaluation of the high-speed ball-end milled surface of hardened AISI D2 steel from a wear resistance perspective. The International Journal of Advanced Manufacturing Technology, 2019, 103(9–12): 4085–4093 https://doi.org/10.1007/s00170-019-03768-1
115
G M Zheng, X Cheng, L Li, R F Xu, Y B Tian. Experimental investigation of cutting force, surface roughness and tool wear in high-speed dry milling of AISI 4340 steel. Journal of Mechanical Science and Technology, 2019, 33(1): 341–349 https://doi.org/10.1007/s12206-018-1236-z
116
Y Li, G M Zheng, X Zhang, X Cheng, X H Yang, R F Xu. Cutting force, tool wear and surface roughness in high-speed milling of high-strength steel with coated tools. Journal of Mechanical Science and Technology, 2019, 33(11): 5393–5398 https://doi.org/10.1007/s12206-019-1033-3
117
G M Zheng, X Cheng, Y J Dong, H B Liu, Y Z Yu. Surface integrity evaluation of high-strength steel with a TiCN-NbC composite coated tool by dry milling. Measurement, 2020, 166: 108204 https://doi.org/10.1016/j.measurement.2020.108204
B Zhao. Study on fabrication and properties of ceramic cutting tools for high-speed machining nickel-based superalloys. Dissertation for the Doctoral Degree. Jinan: Shandong University, 2018 (in Chinese)
120
K Kamdani, S Hasan, A F I A Ashaary, M A Lajis, E A Rahim. Study on tool wear and wear mechanisms of end milling nickel-based alloy. Jurnal Tribologi, 2019, 21: 82–92
121
F Molaiekiya, P Stolf, J M Paiva, B Bose, J Goldsmith, C Gey, S Engin, G Fox-Rabinovich, S C Veldhuis. Influence of process parameters on the cutting performance of SiAlON ceramic tools during high-speed dry face milling of hardened Inconel 718. The International Journal of Advanced Manufacturing Technology, 2019, 105(1–4): 1083–1098 https://doi.org/10.1007/s00170-019-04210-2
122
Y L Zhang, J F Sun, X Shen, W Y Chen. Performance of PCBN tools in high-speed milling nickel-based superalloy. Materials Research Innovations, 2015, 19(sup1): S1-118–S1-125 https://doi.org/10.1179/1432891715Z.0000000001381
123
Y Qiao, X L Fu, X F Yang. An experimental research of dry milling powder metallurgy nickel-based superalloy with coated carbide tools. Advanced Materials Research, 2012, 500: 38–43 https://doi.org/10.4028/www.scientific.net/AMR.500.38
124
F Molaiekiya, A Aliakbari Khoei, M Aramesh, S C Veldhuis. Machined surface integrity of Inconel 718 in high-speed dry milling using SiAlON ceramic tools. The International Journal of Advanced Manufacturing Technology, 2021, 112(7–8): 1941–1950 https://doi.org/10.1007/s00170-020-06471-8
125
Ş Şirin, M Sarıkaya, Ç V Yıldırım, T Kıvak. Machinability performance of nickel alloy X-750 with SiAlON ceramic cutting tool under dry, MQL and hBN mixed nanofluid-MQL. Tribology International, 2021, 153: 106673 https://doi.org/10.1016/j.triboint.2020.106673
126
J Zha, Z L Yuan, H C Zhang, Y P Li, Y L Chen. Nickel-based alloy dry milling process induced material softening effect. Materials, 2020, 13(17): 3758 https://doi.org/10.3390/ma13173758
127
C M Lee, D H Kim, J T Baek, E J Kim. Laser assisted milling device: a review. International Journal of Precision Engineering and Manufacturing-Green Technology, 2016, 3(2): 199–208 https://doi.org/10.1007/s40684-016-0027-1
128
H H Zeng. Research on the mechanism and surface integrity in laser-assisted milling of AerMet100 steel. Dissertation for the Doctoral Degree. Wuhan: Huazhong University of Science and Technology, 2019 (in Chinese)
129
R Singh, S N Melkote. Hybrid laser-assisted mechanical micromachining (LAMM) process for hard-to-machine materials. Journal of Laser Micro Nanoengineering, 2007, 2(2): 156–161 https://doi.org/10.2961/jlmn.2007.02.0010
130
R Singh, S N Melkote. Experimental characterization of laser-assisted mechanical micromachining (LAMM) process. In: Proceedings of the ASME 2005 International Mechanical Engineering Congress and Exposition. Orlando: ASME, 2005, 957–964
131
Y H Jeon, F Pfefferkorn. Effect of laser preheating the workpiece on micro end milling of metals. Journal of Manufacturing Science and Engineering, 2008, 130(1): 011004 https://doi.org/10.1115/1.2783219
132
T Özel, F Pfefferkorn. Pulsed laser assisted micromilling for die/mold manufacturing. In: Proceedings of the ASME 2007 International Manufacturing Science and Engineering Conference. Atlanta: ASME, 2007, 337–342
133
X F Cao, W S Woo, C M Lee. A study on the laser-assisted milling of 13-8 stainless steel for optimal machining. Optics & Laser Technology, 2020, 132: 106473 https://doi.org/10.1016/j.optlastec.2020.106473
134
M J Bermingham, D Kent, M S Dargusch. Dargusch. A new understanding of the wear processes during laser assisted milling 17-4 precipitation hardened stainless steel. Wear, 2015, 328–329: 518–530 https://doi.org/10.1016/j.wear.2015.03.025
135
S Meikote, M Kumar, F Hashimoto, G Lahoti. Laser assisted micro-milling of hard-to-machine materials. CIRP Annals, 2009, 58(1): 45–48 https://doi.org/10.1016/j.cirp.2009.03.053
136
M Kumar, C J Chang, S N Melkote, V Roshan Joseph. Modeling and analysis of forces in laser assisted micro milling. Journal of Manufacturing Science and Engineering, 2013, 135(4): 041018 https://doi.org/10.1115/1.4024538
137
M Kadivar, B Azrhoushang, A Zahedi, C Müller. Laser-assisted micro-milling of austenitic stainless steel X5CrNi18-10. Journal of Manufacturing Processes, 2019, 48: 174–184 https://doi.org/10.1016/j.jmapro.2019.11.002
138
H H Zeng, R Yan, W Wang, H Zhang, J N Yan, F Y Peng. Analytical modeling of the heat-affected zone in laser-assisted milling of AerMet100 steel. The International Journal of Advanced Manufacturing Technology, 2020, 109(9–12): 2481–2490 https://doi.org/10.1007/s00170-020-05821-w
139
D H Kim, C M Lee. Experimental investigation on machinability of titanium alloy by laser-assisted end milling. Metals, 2021, 11(10): 1552 https://doi.org/10.3390/met11101552
140
M S Sim, C M Lee. Determination of optimal laser power according to the tool path inclination angle of a titanium alloy workpiece in laser-assisted machining. The International Journal of Advanced Manufacturing Technology, 2016, 83(9–12): 1717–1724 https://doi.org/10.1007/s00170-015-7684-z
141
W S Woo, C M Lee. A study on the optimum machining conditions and energy efficiency of a laser-assisted fillet milling. International Journal of Precision Engineering and Manufacturing-Green Technology, 2018, 5(5): 593–604 https://doi.org/10.1007/s40684-018-0061-2
142
W S Woo, C M Lee. Laser-assisted milling of turbine blade using five-axis hybrid machine tool with laser module. International Journal of Precision Engineering and Manufacturing-Green Technology, 2021, 8(3): 783–793 https://doi.org/10.1007/s40684-020-00217-3
143
N S Oh, W S Woo, C M Lee. A study on the machining characteristics and energy efficiency of Ti–6Al–4V in laser-assisted trochoidal milling. International Journal of Precision Engineering and Manufacturing-Green Technology, 2018, 5(1): 37–45 https://doi.org/10.1007/s40684-018-0004-y
144
G K Hedberg, Y C Shin, L Xu. Laser-assisted milling of Ti–6Al–4V with the consideration of surface integrity. The International Journal of Advanced Manufacturing Technology, 2015, 79(9–12): 1645–1658 https://doi.org/10.1007/s00170-015-6942-4
145
R Wiedenmann, M F Zaeh. Laser-assisted milling—process modeling and experimental validation. CIRP Journal of Manufacturing Science and Technology, 2015, 8: 70–77 https://doi.org/10.1016/j.cirpj.2014.08.003
146
G K Hedberg, Y C Shin. Laser assisted milling of Ti–6Al–4V ELI with the analysis of surface integrity and its economics. Lasers in Manufacturing and Materials Processing, 2015, 2(3): 164–185 https://doi.org/10.1007/s40516-015-0013-4
147
R Wiedenmann, S Liebl, M F Zaeh. Influencing factors and workpiece’s microstructure in laser-assisted milling of titanium. Physics Procedia, 2012, 39: 265–276 https://doi.org/10.1016/j.phpro.2012.10.038
148
X J Kong, L J Yang, H Z Zhang, K Zhou, Y Wang. Cutting performance and coated tool wear mechanisms in laser-assisted milling K24 nickel-based superalloy. The International Journal of Advanced Manufacturing Technology, 2015, 77(9–12): 2151–2163 https://doi.org/10.1007/s00170-014-6606-9
149
Y G Tian, B X Wu, M Anderson, Y C Shin. Laser-assisted milling of silicon nitride ceramics and Inconel 718. Journal of Manufacturing Science and Engineering, 2008, 130(3): 031013 https://doi.org/10.1115/1.2927447
150
T W Kim, C M Lee. Determination of the machining parameters of nickel-based alloys by high-power diode laser. International Journal of Precision Engineering and Manufacturing, 2015, 16(2): 309–314 https://doi.org/10.1007/s12541-015-0041-1
151
D H Kim, C M Lee. A study on the laser-assisted ball-end milling of difficult-to-cut materials using a new back-and-forth preheating method. The International Journal of Advanced Manufacturing Technology, 2016, 85(5–8): 1825–1834 https://doi.org/10.1007/s00170-015-8014-1
152
E J Kim, C M Lee. A study on the machining characteristics of curved workpiece using laser-assisted milling with different tool paths in Inconel 718. Metals, 2018, 8(11): 968 https://doi.org/10.3390/met8110968
153
X F Wu, W B Zhu, J F Chen. Tool wear mechanisms in laser-assisted milling of nickel-based superalloys. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2021, 43(3): 151 https://doi.org/10.1007/s40430-021-02860-6
154
X F Wu, J F Chen. The temperature process analysis and control on laser-assisted milling of nickel-based superalloy. The International Journal of Advanced Manufacturing Technology, 2018, 98(1–4): 223–235 https://doi.org/10.1007/s00170-018-1809-0
155
Z D Shang, Z R Liao, J A Sarasua, J Billingham, D Axinte. On modelling of laser assisted machining: forward and inverse problems for heat placement control. International Journal of Machine Tools and Manufacture, 2019, 138: 36–50 https://doi.org/10.1016/j.ijmachtools.2018.12.001
156
D D Xu, Z R Liao, D Axinte, J A Sarasua, R M’Saoubi, A Wretland. Investigation of surface integrity in laser-assisted machining of nickel based superalloy. Materials & Design, 2020, 194: 108851 https://doi.org/10.1016/j.matdes.2020.108851
X Y Zhang, Z H Lu, Z L Peng, D Y Zhang. High quality and efficient ultrasonic vibration cutting of titanium alloys. Journal of Mechanical Engineering, 2021, 57(5): 133–147 (in Chinese) https://doi.org/10.3901/JME.2021.05.133
159
F Xue, K Zheng, W H Liao, J Shu, S Dong. Investigation on fiber fracture mechanism of C/SiC composites by rotary ultrasonic milling. International Journal of Mechanical Sciences, 2021, 191: 106054 https://doi.org/10.1016/j.ijmecsci.2020.106054
160
W Q Chen, L Zheng, W K Xie, K Yang, D H Huo. Modelling and experimental investigation on textured surface generation in vibration-assisted micro-milling. Journal of Materials Processing Technology, 2019, 266: 339–350 https://doi.org/10.1016/j.jmatprotec.2018.11.011
161
X Y Zhang, D Y Zhang, H Sui, X G Jiang. Influence of depth of cut on elliptical ultrasonic vibration cutting mechanism. ACTA Aeronauticaet Astronautica Sinica, 2017, 38(4): 420567 https://doi.org/10.7527/S1000-6893.2016.0231
162
D S Lv, J H Xu, W F Ding, Y C Fu, C Y Yang, H H Su. Tool wear in milling Ti40 burn-resistant titanium alloy using pneumatic mist jet impinging cooling. Journal of Materials Processing Technology, 2016, 229: 641–650 https://doi.org/10.1016/j.jmatprotec.2015.10.020
163
C Y Hsu, C K Huang, C Y Wu. Milling of MAR-M247 nickel-based superalloy with high temperature and ultrasonic aiding. The International Journal of Advanced Manufacturing Technology, 2007, 34(9–10): 857–866 https://doi.org/10.1007/s00170-006-0657-5
164
B Fang, Z H Yuan, D P Li, L Y Gao. Effect of ultrasonic vibration on finished quality in ultrasonic vibration assisted micromilling of Inconel 718. Chinese Journal of Aeronautics, 2021, 34(6): 209–219 https://doi.org/10.1016/j.cja.2020.09.021
165
Z H Yuan, B Fang, Y B Zhang, F Wang. Effect of cutting parameters on chips and burrs formation with traditional micromilling and ultrasonic vibration assisted micromilling. The International Journal of Advanced Manufacturing Technology, 2022, 119(3–4): 2615–2628 https://doi.org/10.1007/s00170-021-08468-3
166
A Suárez, F Veiga, Lacalle L N L de, R Polvorosa, S Lutze, A Wretland. Effects of ultrasonics-assisted face milling on surface integrity and fatigue life of Ni-alloy 718. Journal of Materials Engineering and Performance, 2016, 25(11): 5076–5086 https://doi.org/10.1007/s11665-016-2343-6
167
A Suárez, F Veiga, R Polvorosa, T Artaza, J Holmberg, Lacalle L N L de, A Wretland. Surface integrity and fatigue of non-conventional machined alloy 718. Journal of Manufacturing Processes, 2019, 48: 44–50 https://doi.org/10.1016/j.jmapro.2019.09.041
168
Y S Su, L Li. An investigation of cutting performance and action mechanism in ultrasonic vibration-assisted milling of Ti6Al4V using a PCD tool. Micromachines, 2021, 12(11): 1319 https://doi.org/10.3390/mi12111319
169
Y S Su, L Li. Surface integrity of ultrasonic-assisted dry milling of SLM Ti6Al4V using polycrystalline diamond tool. The International Journal of Advanced Manufacturing Technology, 2022, 119(9–10): 5947–5956 https://doi.org/10.1007/s00170-022-08669-4
170
H H Gao, B J Ma, Y P Zhu, H Yang. Enhancement of machinability and surface quality of Ti–6Al–4V by longitudinal ultrasonic vibration-assisted milling under dry conditions. Measurement, 2022, 187: 110324 https://doi.org/10.1016/j.measurement.2021.110324
171
W B Xie, X K Wang, E B Liu, J Wang, X B Tang, G X Li, J Zhang, L Q Yang, Y B Chai, B Zhao. Research on cutting force and surface integrity of TC18 titanium alloy by longitudinal ultrasonic vibration assisted milling. The International Journal of Advanced Manufacturing Technology, 2022, 119(7–8): 4745–4755 https://doi.org/10.1007/s00170-021-08532-y
172
C Y Zhang, B Zhao, C Y Zhao. Effect of ultrasonic vibration-assisted face milling on the surface microstructure and tribological properties. Journal of Vibroengineering, 2022, 24(1): 1–17 https://doi.org/10.21595/jve.2021.21971
173
L H Xu, H B Na, G C Han. Machinablity improvement with ultrasonic vibration-assisted micro-milling. Advances in Mechanical Engineering, 2018, 10(12): 1687814018812531 https://doi.org/10.1177/1687814018812531
174
L D Zhu, C B Ni, Z C Yang, C F Liu. Investigations of micro-textured surface generation mechanism and tribological properties in ultrasonic vibration-assisted milling of Ti–6Al–4V. Precision Engineering, 2019, 57: 229–243 https://doi.org/10.1016/j.precisioneng.2019.04.010
175
X B Wang, F Jiao, C Y Zhao, B Zhao. Modeling and experimental analysis of cutting force in longitudinal‒torsional ultrasonic-assisted milling of titanium. Advances in Mechanical Engineering, 2019, 11(4): 1687814019835107 https://doi.org/10.1177/1687814019835107
176
G F Gao, Z W Xia, T T Su, D H Xiang, B Zhao. Cutting force model of longitudinal‒torsional ultrasonic-assisted milling Ti–6Al–4V based on tool flank wear. Journal of Materials Processing Technology, 2021, 291: 117042 https://doi.org/10.1016/j.jmatprotec.2021.117042
177
P M Rinck, A Gueray, R Kleinwort, M F Zaeh. Experimental investigations on longitudinal‒torsional vibration-assisted milling of Ti–6Al–4V. The International Journal of Advanced Manufacturing Technology, 2020, 108(11–12): 3607–3618 https://doi.org/10.1007/s00170-020-05392-w
178
W F Ren, J K Xu, J Q Lin, Z J Yu, P Yu, Z X Lian, H D Yu. Research on homogenization and surface morphology of Ti–6Al–4V alloy by longitudinal‒torsional coupled ultrasonic vibration ball-end milling. The International Journal of Advanced Manufacturing Technology, 2019, 104(1–4): 301–313 https://doi.org/10.1007/s00170-019-03668-4
179
F Ahmed, T J Ko, R Kurniawan, Y Kwack. Machinability analysis of difficult-to-cut material during ultrasonic vibration-assisted ball end milling. Materials and Manufacturing Processes, 2021, 36(15): 1734–1745 https://doi.org/10.1080/10426914.2021.1944194
180
M Y Tsai, C T Chang, J K Ho. The machining of hard mold steel by ultrasonic assisted end milling. Applied Sciences, 2016, 6(11): 373 https://doi.org/10.3390/app6110373
181
A Maurotto, C T Wickramarachchi. Experimental investigations on effects of frequency in ultrasonically-assisted end-milling of AISI 316L: a feasibility study. Ultrasonics, 2016, 65: 113–120 https://doi.org/10.1016/j.ultras.2015.10.012
182
M R Razfar, P Sarvi, M M A Zarchi. Experimental investigation of the surface roughness in ultrasonic-assisted milling. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2011, 225(9): 1615–1620 https://doi.org/10.1177/0954405411399331
183
P Sarvi Hampa, M R Razfar, M Malaki, A Maleki. The role of dry aero-acoustical lubrication and material softening in ultrasonically assisted milling of difficult-to-cut AISI 304 steels. Transactions of the Indian Institute of Metals, 2015, 68(1): 43–49 https://doi.org/10.1007/s12666-014-0429-0
184
M M Abootorabi Zarchi, M R Razfar, A Abdullah. Experimental investigation of chip formation and surface topology in ultrasonic-assisted milling of X20Cr13 stainless steel. In: Proceedings of the ASME 2013 International Manufacturing Science and Engineering Conference collocated with the 41st North American Manufacturing Research Conference. Madison: ASAM, 2013, V001T01A042
185
H Ding, R Ibrahim, K Cheng, S J Chen. Experimental study on machinability improvement of hardened tool steel using two dimensional vibration-assisted micro-end-milling. International Journal of Machine Tools and Manufacture, 2010, 50(12): 1115–1118 https://doi.org/10.1016/j.ijmachtools.2010.08.010
186
M M Abootorabi Zarchi, M R Razfar, A Abdullah. Influence of ultrasonic vibrations on side milling of AISI 420 stainless steel. The International Journal of Advanced Manufacturing Technology, 2013, 66(1–4): 83–89 https://doi.org/10.1007/s00170-012-4307-9
187
K V Rao, V U S V Prasad, B S Ben. A comparative study on cutting forces and power consumption in plain and ultrasonic vibration helical milling of AISI 1020 steel. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2022, 236(13): 1726–1737 https://doi.org/10.1177/09544054221089438
188
H Ding, S J Chen, K Cheng. Two dimensional vibration-assisted micro-milling: kinematics simulation, chip thickness computation and analysis. Advanced Materials Research, 2010, 97‒101: 2779–2784 https://doi.org/10.4028/www.scientific.net/AMR.97-101.2779
189
B Y Qi, N He, L Li, W Zhao, R Bian. Cryogenic minimum quantity lubrication technology and its action mechanism. Mechanical Science and Technology for Aerospace Engineering, 2010, 29(6): 826–831, 835 (in Chinese)
190
O Pereira, A Rodríguez, J Barreiro, A I Fernández-Abia, L N López-de-Lacalle. Nozzle design for combined use of MQL and cryogenic gas in machining. International Journal of Precision Engineering and Manufacturing-Green Technology, 2017, 4(1): 87–95 https://doi.org/10.1007/s40684-017-0012-3
191
N S Ross, C Gopinath, S Nagarajan, M K Gupta, R Shanmugam, M S Kumar, M Boy, M E Korkmaz. Impact of hybrid cooling approach on milling and surface morphological characteristics of Nimonic 80A alloy. Journal of Manufacturing Processes, 2022, 73: 428–439 https://doi.org/10.1016/j.jmapro.2021.11.018
192
O Pereira, P Català, A Rodríguez, T Ostra, J Vivancos, A Rivero, L N López-de-Lacalle. The use of hybrid CO2 + MQL in machining operations. Procedia Engineering, 2015, 132: 492–499 https://doi.org/10.1016/j.proeng.2015.12.524
193
K Nimel Sworna Ross, G Manimaran, S Anwar, M A Rahman, M E Korkmaz, M K Gupta, A Alfaify, M Mia. Investigation of surface modification and tool wear on milling Nimonic 80A under hybrid lubrication. Tribology International, 2021, 155: 106762 https://doi.org/10.1016/j.triboint.2020.106762
194
L Sterle, D Mallipeddi, P Krajnik, F Pušavec. The influence of single-channel liquid CO2 and MQL delivery on surface integrity in machining of Inconel 718. Procedia CIRP, 2020, 87: 164–169 https://doi.org/10.1016/j.procir.2020.02.032
195
A Shokrani, V Dhokia, S T Newman. Hybrid cooling and lubricating technology for CNC milling of Inconel 718 nickel alloy. Procedia Manufacturing, 2017, 11: 625–632 https://doi.org/10.1016/j.promfg.2017.07.160
196
A Shokrani, S T Newman. Hybrid cooling and lubricating technology for CNC milling of Inconel 718 nickel alloy. Procedia CIRP, 2018, 77: 215–218 https://doi.org/10.1016/j.procir.2018.08.291
197
S Şirin, Ç V Yıldırım, T Kıvak, M Sarıkaya. Performance of cryogenically treated carbide inserts under sustainable cryo-lubrication assisted milling of Inconel X750 alloy. Sustainable Materials and Technologies, 2021, 29: e00314 https://doi.org/10.1016/j.susmat.2021.e00314
198
S Zhang, J F Li, Y W Wang. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions. Journal of Cleaner Production, 2012, 32: 81–87 https://doi.org/10.1016/j.jclepro.2012.03.014
199
A Bagherzadeh, E Kuram, E Budak. Experimental evaluation of eco-friendly hybrid cooling methods in slot milling of titanium alloy. Journal of Cleaner Production, 2021, 289: 125817 https://doi.org/10.1016/j.jclepro.2021.125817
200
N Hanenkamp, S Amon, D Gross. Hybrid supply system for conventional and CO2/MQL-based cryogenic cooling. Procedia CIRP, 2018, 77: 219–222 https://doi.org/10.1016/j.procir.2018.08.293
201
C Y Cai, X Liang, Q L An, Z R Tao, W W Ming, M Chen. Cooling/lubrication performance of dry and supercritical CO2-based minimum quantity lubrication in peripheral milling Ti–6Al–4V. International Journal of Precision Engineering and Manufacturing-Green Technology, 2021, 8(2): 405–421 https://doi.org/10.1007/s40684-020-00194-7
202
M A Suhaimi, G D Yang, K H Park, M J Hisam, S Sharif, D W Kim. Effect of cryogenic machining for titanium alloy based on indirect, internal and external spray system. Procedia Manufacturing, 2018, 17: 158–165 https://doi.org/10.1016/j.promfg.2018.10.031
203
K H Park, G D Yang, M A Suhaimi, D Y Lee, T G Kim, D W Kim, S W Lee. The effect of cryogenic cooling and minimum quantity lubrication on end milling of titanium alloy Ti–6Al–4V. Journal of Mechanical Science and Technology, 2015, 29(12): 5121–5126 https://doi.org/10.1007/s12206-015-1110-1
204
A Shokrani, I Al-Samarrai, S T Newman. Hybrid cryogenic MQL for improving tool life in machining of Ti–6Al–4V titanium alloy. Journal of Manufacturing Processes, 2019, 43: 229–243 https://doi.org/10.1016/j.jmapro.2019.05.006
205
Y Su, N He, L Li. Effect of cryogenic minimum quantity lubrication (CMQL) on cutting temperature and tool wear in high-speed end milling of titanium alloys. Applied Mechanics and Materials, 2010, 34–35: 1816–1821 https://doi.org/10.4028/www.scientific.net/AMM.34-35.1816
206
K H Song, D W Lim, J Y Park, S J Ha, G S Yoon. Investigation on influence of hybrid nozzle of CryoMQL on tool wear, cutting force, and cutting temperature in milling of titanium alloys. The International Journal of Advanced Manufacturing Technology, 2020, 110(7–8): 2093–2103 https://doi.org/10.1007/s00170-020-05646-7
207
S J Ha, D W Kim, J H Kim, J Y Park, K H Song. Economic evaluation and machining performance in Ti–6Al–4V titanium alloy milling by integrated CO2 & MQL injection system. Journal of Mechanical Science and Technology, 2021, 35(9): 4135–4142 https://doi.org/10.1007/s12206-021-0825-4
208
Y H Yuan, C Y Wang, J Z Yang, L J Zheng, W Q Xiong. Performance of supercritical carbon dioxide (scCO2) mixed with oil-on-water (OoW) cooling in high-speed milling of 316L stainless steel. Procedia CIRP, 2018, 77: 391–396 https://doi.org/10.1016/j.procir.2018.08.301
209
K K Wika, P Litwa, C Hitchens. Impact of supercritical carbon dioxide cooling with minimum quantity lubrication on tool wear and surface integrity in the milling of AISI 304L stainless steel. Wear, 2019, 426–427: 1691–1701 https://doi.org/10.1016/j.wear.2019.01.103
210
G Manimaran, K Nimel Sworna Ross. Surface behavior of AISI H13 alloy steel machining under environmentally friendly cryogenic MQL with PVD-coated tool. Journal of Testing and Evaluation, 2020, 48(4): 3269–3280 https://doi.org/10.1520/JTE20180130
211
H P Zhang, Q Y Zhang, Y Ren, T Shay, G L Liu. Simulation and experiments on cutting forces and cutting temperature in high speed milling of 300M steel under CMQL and dry conditions. International Journal of Precision Engineering and Manufacturing, 2018, 19(8): 1245–1251 https://doi.org/10.1007/s12541-018-0147-3
212
H P Zhang, C L Ding, R X Shi, R H Liu. Optimization of technological parameters and application conditions of CMQL in high-speed milling 300M steel. Integrated Ferroelectrics, 2021, 217(1): 141–153 https://doi.org/10.1080/10584587.2021.1911306
213
S Zhang, J F Li, H G Lv. Tool wear and formation mechanism of white layer when hard milling H13 steel under different cooling/lubrication conditions. Advances in Mechanical Engineering, 2014, 6: 949308 https://doi.org/10.1155/2014/949308
214
C L Zhang, S Zhang, X F Yan, Q Zhang. Effects of internal cooling channel structures on cutting forces and tool life in side milling of H13 steel under cryogenic minimum quantity lubrication condition. The International Journal of Advanced Manufacturing Technology, 2016, 83(5–8): 975–984 https://doi.org/10.1007/s00170-015-7644-7
